Discussion Locked

Why is USB2 port acting like USB1.1?

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I recently got a new pre-built Acer (AMD64 x2 3800, 1G, 250G, mobo FC51GM) that says it has 8 USB2.0 ports. However a reminder keeps popping up that says my USB root hub would work faster if it were connected to a high speed port, click here for a list of ports. The list says there are no high speed ports installed.

I have Windows Media Center installed with SP2. I have uninstalled the whole USB port structure and restarted so that XP SP2 could install the 2.0 drivers, but it does not do so. Several emails to the dealer and to Acer have gone unanswered. I can't quite match mobos on the Foxconn site to the FC51GM that Acer says is its mobo, and I don't see anything there about USB drivers anyway.

I don't have a mobo disk or a separate OS disk, only the 'recovery' disks from Acer and I am loathe to try them because I fear it will wipe out all the setup and programs I have installed.

Any suggestions? Thanks!

9 replies

by hal 9000

Quite often with the Non Intel M'Boards you need to install the Proper Drivers for the USB 2 Ports as the default drivers supplied with Windows will work but not necessarily correctly. I would visit the Acer Site and download the newest available USB Drivers for your particular model and install those after first making sure that the USB ports are being picked up in Windows.

Col

by neige

Thank you for the BIOS suggestion. I did check the BIOS and it is set for USB2.0/1.1.

Windows update says everything is current.

It is a bit frustrating when some suggest that I do things that I have already said I have done.

I have gone to MS to get the latest SP (I have SP2)

I have gone to the Acer website and they do not list any USB drivers. If I had any idea where to get the USB drivers I would do so in a heartbeat.

Please excuse the frustration - I've been asking for two weeks at my dealer, at Acer, and on other tech sites. Almost all of the advice I am getting is telling me to do things I have already done and have so stated in my description of the probelem.

Still open to suggestions. Thanks.

by exp

Has ever worked after you got it? If not there may be something wrong with the mobo. Most new mobo don't need USB driver they are integerated with the system driver eg like to VIA 4 in 1 etc. Try to find out what chipset your mob use or look at the USB controller properties in the device manager.

by neige

For Exp:
It may be a quirk of the mobo - Foxconn as a private label for Acer. As I noted I have Win MCE 2005 with SP4 so all USB drivers should be up to date, and Windows update says I have everything current. I got some help tracking down the mobo manufacturer and updated all the drivers. I checked the BIOS for USB2, I looked at MS Knowledge Base and made sure I had all the right files in all the right directories and had followed all MS recommended steps. I followed all the advice from all the tech boards and still no joy. Device Manager still showed generic USB drivers installed, not enhanced. I could not get Windows to install the correct driver for the 8 USB2 ports that were on the board.

Finally I got an RMA from the dealer. Just before I was about to pack it up I tried a new thing. I installed an old PCI expansion card with 4 USB2.0 ports. Suddenly the rear factory installed mobo ports were running at USB2, as was the factory installed card reader, and the PCI card ports.

I don't know what to make of that. Certainly there was some disconnect between the board and the OS. Why this outside card made it possible to finally connect the drivers to the mobo I don't know.

I certainly don't want to uninstall the card. The deal I got on the rig was quite a good one, so if it takes this quirky workaround to run, so be it.

Thanks for asking!

by dondlelinger

I've got the exact same system as you.
I also experienced this problem.
I had another problem with two of four RAM slots not ready new memory sticks. I moved all my programs and drivers that I installed to my partioned D: drive. Then I ran the recovery disks. Surprisingly enough...it worked. The USB read as 2.0 and the other RAM slots decided to work. ps.The people at Acer tech. support might as well flip burgers at McD's

by garyn

I have exactly the same problem. I had to reinstall windows xp pro after xp home became unstable.
Have installed service pack 2 and been to all the windows update sites still no go.
I rang acer customer support and they were absolutely useless tellin me i had voided the warranty because of the xp pro update.
This was the excuse they used to deny me any help except to mutter somethin about a chip set before cutting me off!
I will never by another acer product again.

by neige

dondelinger - Thanks for the validation! I agree about Acer support - somewhat less useful than an 8" floppy. My RAM slots are working okay - I added another gig myself.

I'll bet this is why this rig, and yours, was RMA'd in the first place - and why they sent it out unfixed again. Very tacky.

Neige

This discussion is closed to new replies.