Discussion Locked

Win98 max resolution 800x600 w/ Geforce3

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I used to have a 4MB Diamond Stealth Pro 2D (PCI) video board in my computer, coupled with a Voodoo2 (PCI) for 3D acceleration.
With those video boards installed, I could run a resolution of 1024x768, at a refresh rate of 87Hz, with no problems.
I recently upgraded to a Geforce3 Ti200 (AGP) video board, and now I cannot get my screen resolution to go above 800x600 while in Windows. The strange thing is, if I'm playing Unreal Tournament, I can change the game resolution to 1024x768, but the screen resolution stays at 800x600, so the game is bigger than the screen...

I am running Win98SE. I have the most recent updates for my OS, and the most updated drivers for my monitor (NEC Multisync 75 - driver date 12/3/2001) and my Geforce 3 (detonator drivers, dated 11/29/2001).

As far as I can tell, all BIOS settings are correct and I have removed all traces of old video drivers from windows.

I have tried different refresh rates. I tried everything from 60 to 100 Hz, but I cannot get the resolution higher than 800x600. When I try, the monitor seems to change modes, but when Windows comes back, asking if I want to "keep this setting", the resolution is still at 800x600.

Does anyone have any ideas? I am about out of them.
I appreciate any input.

6 replies

by thechas

Have you updated the AGP miniport driver for your motherboard?

I would also check for a BIOS update for the motherboard.

What version of DirectX are you running?
Many video drivers require a specific version of DirectX.

I was just at Nvidia's site, and the current version of Detonator is 23.11

You can also try changing to a "standard" svga monitor. I have seen several monitor drivers that had errors in display resolution, and the standard windows monitor driver worked better than the mfg driver.

by thechas

A couple more thoughts;

In BIOS settings;
set primary display adapter to agp.
set agp mode to normal
set agp apperature to somewhere between double the card memory, and 1/2 system ram.

It is also possible that there are a few remnats of theold video drivers hanging around and gettin in the way.
You can use either msconfig, or sysedit to look for some of the references.

If you are familier with it, you can use regedit to remove most of the remnent references.
WARNING!!! IMPROPER REGISTRY EDITING CAN DISABLE YOUR SYSTEM.
It is good practice to back up the registry before editing.
I would use the search function, and search on the names and nicknames of your old graphics cards. It can be amazing what is left behind from an old card or program.

You can also search the windows folders for leftover files for the old cards.

by tscjparker

I changed the BIOS settings as recommended, and this still did nothing to help the issue. I went through and cleared out all the files in the Windows dir that were associated with past video boards, and still it would only show 800x600.

I *did* finally fix the problem, and the solution I found worked best was to upgrade to Win2000 :)
The card is working fine now, and I can now crank up my resolution as high as I want to :)

Thank you for all your ideas, though. I appreciate the help :)

by cvjack

Go to 'Display Properties' and click the 'Settings' tab. Click the 'Advanced' button. Click the 'Monitor' tab then the 'Change' button. Click the 'Display a list.....' option then 'Next'. Click the 'Show All Hardware' option. In the left hand panel select '(Standard Monitor Types)'. In the right hand panel select 'Super VGA 1024x768 @ 75Hz'. Click 'next' and 'OK' enough times to get you back to the Display Properties 'Settings' screen. Move the slider to 1024x768 and hit 'Apply'. That should doit. Win98 sometimes gets confused when you install a new video card and will select 'Default monitor' or 'Plug'n'Play monitor' on it's own. Switching to Super VGA 1024x768 forces Win98 to send the higher resolution screen. If you want, you may be able to re-select the driver that came with your monitor and have it work okay now, but don't be surprised if your 800x600 screen comes back. One more thing you might try, if you haven't already, uninstall the detonator drivers and set your adapter to Standard VGA. Reboot then reload the detonator drivers. Good luck.

by tscjparker

Done and done. Win98 still wouldn't show a resolution higher than 800x600 while using that video board.

I *did* finally fix the problem, and the solution I found worked best was to upgrade to Win2000 :)
The card is working fine now, and I can now crank up my resolution as high as I want to :)

Thank you for all your ideas, though. I appreciate the help :)

This discussion is closed to new replies.