Discussion Locked

Your Suggestions for a hardware toolkit

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I am about to purchase tools to assemble a hardware repair/service tool kit. I would be interested in hearing what tools I should purchase. I work on a variety of PCs and Servers and perform component repair and assembly. I am trying to avoid buying the low quality Belkin-type kit and I do not have the funds for a top of the line ESD kit. I have about $100 and I would like to buy the tools at a Sears or similar store. Any suggestions?

20 replies

by aqmike

the repair kit that I have, I bought from CompUSA for about $75. It has most everything you will need for repair many PCs. I believe the brand name on it is Curtis. Hope this points you in the right direction.

by aqmike

I found the exact name of the toolkit I was talking about. It is the Curtis 145 piece Deluxe Toolkit.

by grump

So now that you already work on the computers and such. Take your $100 and buy the tools you need, get quality tools and any old laptop case will serve for a case to carry them in.. Some fancy case does not make the better technician.. Motion Tools is a good source of all the tools you will need.
I carry my tools in a zipper bank bag.. The tools which I seldom need I leave in the trunk in a plastic shoe box ($.99 Walmart).
Been doing this for close to TWENTY years and still have not spent a lot of money on any fancy case.. Replaced a lot of tools during that time. Keep a smile on your face and no body knows what you are thinking!

by jereg

While there are all kinds of tools you (and I) would like to have, you can really get by on very little. When I went through Compaq Hardware Training, they gave us a screwdriver with 6 bits in the handle. With that one screwdriver I can work on every Compaq PC or server made. (It even works on other brands). That said, here is what I would carry: A great set of screwdrivers from Sears or Home Depot, NOT the crap they sell in computer stores/Radio Shack. It shoulh be a handle with a long shank with replacible bits on the end, yes, magnitized is ok. Or, just a handle with replacible shafts with a different bit on each shaft. both have pros and cons. You need several phillips, flat head, torx, and what ever else they have. If you can get bit drivers in the set as well, bonus. A GOOD set of needle nose pliers and cutters(dikes). Those are my must have tools. That should run you no more that $60. With the left over money, you may consider a small flashlight (my best friend for tired eyes).A parts claw/retrevier for screws dropped in cases can be handy too, $2-3. If you want to spend a little more, maybe look for some kind of cable testers, depending on what kind of work you're doing. BTW, the Compaq screwdriver they gave us can be purchased for about $35 from Compaq. Most of the time, I just use that and a set of folding/geek pliers on my belt.
Hope that helps.

by jereg

a note.
I was shocked when completing the Compaq service course they gave us the screwdriver with a magnatized tip (for bits). The instructor said the field is weak, and you're only using it briefly, so there wans't any problem. Since a magnatized tip tool is Compaq issue for their techs, I guess it's ok.

by hunter_french

I would like to see specific tool recommendations as well as your opinion about magnetic vs. non-magnetic tools.

by marcusestes

May I suggest the Victorinox Cybertool 41. I had been carrying a small case with screwdrivers, etc, but this has it all on it...even a DIP switch setter! It has several torx, flathead, and philips bits, and fits in my pocket! About $60.

Marcus
Brookshire Grocery Co.
PC/LAN Support

by paul.manning

I have been a field tech for 10 years. The 2 essentials are a swiss army knife with the scicors and a $7.00 multibit screwdriver from sears. It has 2 torx,a 10 and a 15, 2 philipps and 2 flat heads. In my car I keep the dykes, European and american allen wrenches, black elecricians tape, and a variety length of cable ties. For rack building I keep a sears 3/8 ratchet set.

by maxwell edison

Greetings,

Forget about all those Pre-packaged kits. Most of them have cheap quality tools for a high dollar cost. And they have tools you'll never use, like chip pullers, pushers and mashers - or whatever they are. Who cares if it slices and dices? Why buy a tool you don't need, nor will ever use?

I like your Sears idea - none better than Craftsman - and they'll replace it for free if it ever fails or gets damaged - even the screwdrivers. Whether you buy a screwdriver with replaceable heads, or several screwdrivers, it's a matter of preference - and budget. Personally, I don't like the one handle fits all heads. It's too much trouble replacing the little screwdriver bits, and they're easier to overlook and lose. I have two phillips and two standard screwdrivers - one small and one medium in size. They have rubber covers on the handle, and good strong, sturdy heads that won't get damaged because of prolonged use or slippage. And I don't use magnetized ones. I don't care what anyone says, I don't want even the weakest magnet anywhere near one of my hard drives if I don't have to. I'll error on the side of caution. And besides, you don't need the magnetized screwdriver (which is more expensive, anyway) when you can have a GLUE STICK. With a dab of glue from a glue stick on the head of a screwdriver, you can reach into the tightest spot - upside down, if necessary - without dropping the screw into a case. And a magnet can't reach down and pick up a dropped insulation washer, and a pair of pliers might not be able to grip it, but a dab of glue on the screwdriver will pick up anything. (I prefer the purple glue stick.)

(continued in comments...)

by maxwell edison

.
.A couple of different sized nut drivers are needed. I don't know the "numbered" size right off hand, but I'm sure you know the two sizes I'm talking about.

Every now and then you'll run across those torque screws, but they are limited to onlya few different sized. I do have a replaceable head driver for those, with the different heads stored in the handle. But I rarely use it.

A pair of (Craftsman) wire cutters, needle nose pliers, and regular pliers (all the small size) are needed. Make sure they have the rubber handles. (I have the red ones.)

A pair of scissors comes in handy; a small penlight (flashlight) is useful at times; have a handful of wire ties (a variety of sizes); and a razor knife - the small, sleek kind wallpaper hangers use (Olfa brand). And don't forget the electrical tape and a pencil.

I do have a nice (and expensive) leather, folding zipper pouch for my tools. But it's certainly not necessary. If cost is a factor, a plastic lunch box (or anything similar) if fine. I know a guy who uses a Looney Toons Lunch Box for his job at an elementary school. Get creative. Let your personality and sense of humor come to light (if you're so inclined).

You can easily outfit your toolbox for under a hundredbucks, and have money left over for several lunches.

Regards,

Maxwell

by wanabedrsean

Your tool selection really depends on the type of equipment your going to be working on. You need to buy tools that have the most possible uses for the size of package that their in. also are you going to be working on printer and plotters also or just computers. What level of repair will you most likely be performing (part swapping or in-depth troubleshooting and component replacement)? Your knowledge has a lot to do with how you repair things and what you repair, which in turn tends to dictate what tools you need. I do think that the Compaq tool kit is a necessity if you work on Compaq or hp server?s pc's or laptops. But if you work on printers, that screwdriver will not suffice all the time. The collar on the shaft that holds the bit inand contains the magnet is too broad to fit in some spaces so you need just a regular screwdriver, for instance if you are working on a LaserJet 3 which is an old printer but an excellent example of the xerographic printing process you will break pieces off of the fuser if you try to take the right side rear screw out with it a Compaq type screwdriver. You will also need a t20 bit and a set of stubby screwdrivers for many hp printers and plotters. Always carry a small flashlight and a spring hook with you if you work on printers.
The best tool to have is a well-equipped brain and a good idea of where to find technical information about whatever it is you work on.

PS I would like to see the liquid nitrogen cooled super conducting electro magnetic screwdriver that could generate a field sufficient enough to damage data on the surface of an encased hardisk platter. The space between the head and the platter is so minute that after about a millimeter it would be tough to hurt a harddisk platter that wasn't encased in aluminum with your (magnetic screwdriver) however you wouldn?t want to get your screwdriver too close to a old 5.25" floppy for very long.

This discussion is closed to new replies.