Question Locked

Can somebody recommend stress testing software(s)?

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

looking for free software(s) to stress test...

Memory
Hard Drive
CPU

*And for Bonus points!* :)

Fan/temp monitoring software

Thank YOU!

13 replies

by rob miners

but someone may add some more.

You can test the memory by running Windows Memory Diagnostic that can be downloaded from http://oca.microsoft.com/en/windiag.asp. If memory problems are found, try re-seating the RAM. If it doesn't work, replace the defective RAM.

You can use the Hard Drive Makers Testing Utility to Test the Drive which can be downloaded from below.
Hitachi / IBM
Western Digital
Fujitsu
Seagate
Samsung

Test the Power Supply Unit with Prime95.

http://www.mersenne.org/freesoft.htm

Prime95 is used to put your system at full load. You want your system at full load when checking your voltages to ensure your PSU is up to spec. The whole point is to make sure your PSU can handle what your system asks of it. When it is installed run it and go to Options and run the Torture Test. Run the Inplace FFTs (Max Power, Heat and some Ram).
If your PC restarts during this test you have a faulty Power Supply (PSU) and it will need replacing.

Download SpeedFan and check the Voltages and Temps while Prime95 is running.

http://www.almico.com/sfdownload.php

Video Memory Stress Test 1.4

http://www.majorgeeks.com/Video_Memory_Stress_Test__d5896.html

Tip! To discharge the Capacitors in the Power Supply & MotherBoard

Remove the Power cord from the PSU to discharge the Capacitors in the Power Supply. Then press the Power button for 30 seconds to discharge the Capacitors on the Motherboard.

by slayer_

What does a good voltage rating look like?

by rob miners

You will want your 12-volt rail to be within 11.52 to 12.48 during load. This means when you are running your cpu at 100% you do not want to drop below 11.52 or you may experience stability problems including but not limited to system restarts and Windows crashes. For the 5-volt rail, you want it to be within 4.8 to 5.2 to be within the 4% range. As for the 3.3 volt rail, you want it to be within 3.17 to 3.43

by slayer_

I just tried it on my work machine, it doesn't detect the PSU.

My home one is really odd tho

the +3.3 shows 0
the +5 shows 7.73
the +12 shows 11.58
the -12 shows -16.97
the -5 shows -8.78
the vbat shows 2.96V
and the vcore shows 0.00
then is shows a final 3.3 @ 3.22V

This is when it is not under load.

So is that bad? I have never had the system randomly shut down. And I have gamed on it and ran it hard for days on end without stability problems

by slayer_

They didnt change at all, so I fired up Last Remnant WHILE running those tests, still didn't bother it. GPU Temperature went from 33C to 55C, that was biggest difference, everything else stayed the same. So I guess my PSU is good. My system must be freakin awesome :). However, I tried this same test on a system, I am fairly certain has a weak PSU, and it didn't shut it down or show any bad readings. So I am not sure how reliable this actually is.

I know the system is bad cause, without a video card, often in games it would just shut down, or it would just sit around and then shutdown magically. I recently stuck a low powered AGP video card in it, and it far more frequently shuts down, I actually had it shut down on me 3 times in a row within 2 minutes. But it was fine for 5 hours of running that stress test and having a game running in the background. Go figure...

by older mycroft

My 8800GT has a [b][u]minimum[/b][/u] of 53' !!
[i](That's with the fan running @ 80%)[/i]

by slayer_

I have a really well ventilated case :), but its a 9600 GT. I have it super insanely overclocked :) (Blowing it up would give me a reason to upgrade, but the damn thing refuses to blow, it actually runs cooler the higher I OC it)

by slayer_

No, I don't have a digital one.

Too bad there is not a better software way to tell :(.

Also damn shame the card I stuck in is ATI, so I can't use nTune to stress test it properly.

by jdclyde

soft but able to test the levels of resistance......

This discussion is closed to new replies.