Question Locked

Please Help!! Updating Motherboard drivers...

0 helpful
14 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Please help. I haven't swam too deep into hardware issues so excuse me if this is just simple. Trying to update my motherboard driver. Have an ASUS P5N-E SLI and have DL'd the drivers, but they appear to be just copies of what would be on a retail drivers/utilities disk minus the setup utility, and most of the drivers available for download do not have a standalone setup/installation utility of their own either. Can anyone help me??

I'm seeing that this new computer is not running USB 2.0 but hopefully that can be resolved with this installation.

14 replies

by oh smeg

They have always been listed on the M'Board CD and I can not see ASUS changing that now. But maybe the Menu isn't working correctly and you need to open the actual ASUS CD navigate to the Driver Section and install directly from there. Or you are attempting to install drivers that are not supported by ASUS for your OS.

Failing that the correct Drivers for your M'Board are here but you have to chose your OS and then download the drivers for your M'Board that suit your OS and install them after unzipping them.

http://tinyurl.com/9qlck

The only possible problem here is that you may be attempting to install drivers that are not suitable for your OS and this is causing the problem to occur. But at the listed Web Site ASUS has Drivers for Windows XP, 2003, 2000 in the 32 & 64 Bit Versions and some 32 Bit Vista Drivers so I'm assuming that they do not support Drivers for the older versions of Windows like ME 98 and so on or Vista 64.

As for the USB 2 Support this is restricted to the OS you are using as XP prior to SP2 doesn't have any USB2 Support and any installed USB Devices will only run at USB1.1 or at least that is how they appear in Device Manager. Windows 98 SE was the only version of 98 that supported USB and that only supported USB1.1 so this is very much OS Dependant.

Col

by pwmulder

yes i am using vista 32 (ultimate) so usb 2.0 should work fine. The drivers on for the motherboard have just been updated so using those on the CD won't resolve my problem as I would need to install the updated ones from the site to get the current.

So here's where it gets tricky. Would I have to burn these files onto a CD then boot from that CD to have these installed?

Again, the files are for the motherboard ASUS P5N-E SLI and I can just download them again but how can i install them?

I found out that for the USB ports that it might just be the voltage that I'll have to change in BIOS from 1.8 to 2.1, and if that's not the problem I've got to check the heatsink which might be tricky.

It would just be so much easier if Asus offered some utility to analyze your MB for possible updates.

by oh smeg

What you need to do here is download the Driver/s to a Temp Folder on the HDD unzip them with Win Zip or a similar Utility and then when you left click on the Unzipped File it installs itself.

As for the USB Issue this is a Basic BIOS Setting that should have been performed when you originally setup the Computer. ASUS Provide a very well written User Manual exactly for this purpose to prevent problems latter.

As for using the newest drivers this is unnecessary unless you are experiencing problems with your computer doing something. It's generally a unnecessary job to perform and if you want to go crazy you wouldn't look at the M'Board Makers Web Site but the Chip Set Makers Web Site for the newest drivers that they make for this Chip Set.

Of course that may not work with your M'Board as some functions of the Chip Set may not be currently being utilized but you will have the newest drivers possible for your M'Board.

OH BTW you can download the User Manual in PDF Format at the same site that I posted above as well.

Col

by pwmulder

yes i am using vista 32 (ultimate) so usb 2.0 should work fine. The drivers on for the motherboard have just been updated so using those on the CD won't resolve my problem as I would need to install the updated ones from the site to get the current.

So here's where it gets tricky. Would I have to burn these files onto a CD then boot from that CD to have these installed?

Again, the files are for the motherboard ASUS P5N-E SLI and I can just download them again but how can i install them?

I found out that for the USB ports that it might just be the voltage that I'll have to change in BIOS from 1.8 to 2.1, and if that's not the problem I've got to check the heatsink which might be tricky.

It would just be so much easier if Asus offered some utility to analyze your MB for possible updates.

by thechas

It is very possible that the drivers on the ASUS web site are the same version as what is on the CD that came with the motherboard.

You should be able to look at the version or release date of the driver on the web site to see if it is a newer version than what came on the CD.

As far as installing the drivers, I usually install the motherboard drivers in this order:

Chip-Set
AGP mini-port (if present)
Video driver (whether on-board or a card)
Storage controllers (SATA or secondary IDE)
USB
Other on-board peripherals

Note, make sure to check the BIOS setup options for the USB ports, and make sure any case wiring is up to USB 2 standards.

Chas

by pwmulder

Yeah I know this get iffy. yes i am using vista 32 (ultimate) so usb 2.0 should work fine. The drivers on for the motherboard have just been updated so using those on the CD won't resolve my problem as I would need to install the updated ones from the site to get the current.

So here's where it gets tricky. Would I have to burn these files onto a CD then boot from that CD to have these installed?

Again, the files are for the motherboard ASUS P5N-E SLI and I can just download them again but how can i install them?

I found out that for the USB ports that it might just be the voltage that I'll have to change in BIOS from 1.8 to 2.1, and if that's not the problem I've got to check the heatsink which might be tricky.

It would just be so much easier if Asus offered some utility to analyze your MB for possible updates.

by thechas

Now I understand your question.

Depending on the download, there are 3 different ways to install the updated driver.

Preliminary:
If the download is a .ZIP file, you need to extract the files from the ZIP archive.
What I do, is set up a folder on the system hard drive labeled Drivers or ASUS.
I then download the files to that folder and extract the files from the archive.
Windows Explorer has this built in. Just browse to the ZIP file, double click on it and choose extract all files.
Pay attention to the folder name for the extracted files.

1. Self Extracting Archive:
Most drivers are in self extracting archive files. These are just like the ZIP files, except they extract themselves. Many of these also automatically run a setup program and install the driver.

2. Extracted files with a Setup.exe file. Always read the readme file that comes with most drivers. It usually has installation instructions and tips.
Run setup.exe for the driver and follow the prompts.

3. Extracted files and .INI files
When there is no setup or other executable file, you need to install the driver manually. (Again, check the readme file.)
Open Device Manager.
Right click on the device that the driver is for and select Update Driver.
From the driver wizard, select have disk and browse to the folder where the driver files are.
Windows will not install the driver if it does not match the hardware, or is an older version.

All of the above stated, I still doubt that your USB problem is a driver issue.
Enter BIOS setup.
From the advanced menu, select USB configuration.
Make sure that the USB 2.0 Controller is set to Enabled.

Also, looking at the ASUS web site, there is an unusally high number of BIOS versions. The latest is date 7/7/08 and has a cryptic line about Vista compatibility.

http://support.asus.com/download/download.aspx?SLanguage=en-us

The manual for this board covers BIOS updates in good detail. Just make sure that if you do update the BIOS that you follow all of the precautions and steps.

Chas

by pwmulder

Alright, I'll check it out thank you very much.

by Former member

http://www.versiontracker.com/dyn/moreinfo/win/32569
And when it has downloaded you will have a choice to extract it (install) and it will do the rest. You might need to re-boot your computer on some of the programs/software.
This is just an alternative if you need it.

Please post back if you have anymore problems or questions.

by older mycroft

The latest 2 updates are only if the CPU is sufficiently advanced as to be unrecognised by the existing BIOS version.

When my motherboard was replaced recently, it proved to have an older BIOS version, which wouldn't recognise my Core 2 Duo E8500.

However, if a user updates because the BIOS version is 'newer' and they don't have the newer CPU, the update will fail on boot.

This discussion is closed to new replies.