Question Locked

USB-HDs and sticks dosent show up in ?"my computer" on XP clients

0 helpful
3 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello

I run a windows 2003 domain and have some trouble when users tries to use there USB-sticks and USB-harddrives in XP sp2.

1) When i log in as a admin the USB-sticks installs " ready for use" and shows it self under "my computer".

1) When i log as a user the sticks installs " ready for use" and but it dont show it self in "my computer". !!!

thanks for your help.

3 replies

by siska

I run a windows 2003 domain and have some trouble when users tries to use there USB-sticks and USB-harddrives in XP sp2.

1) When i log in as a admin the USB-sticks installs " ready for use" and shows it self under "my computer".

1) When i log as a user the sticks installs " ready for use" and but it dont show it self in "my computer". !!!

I have the same problem did you get some solution? thamks Marek Siska, Istrokapital Slovakia

by Former member

To run USB devices, you might have to put in the ADMIN password and user name. You might be able to get these devices running under group policy.

OR try this:

Windows XP or Windows Server 2003 does not detect your new USB device

SYMPTOMS
When you connect a new USB device to a computer that has no USB devices, Windows XP and Windows Server 2003 may not detect the new device.

CAUSE
This problem may occur because, when no device is connected to a USB port, the USB driver sets the Open Host Controller Interface (OHCI) controller to suspend. When the OHCI controller is in a suspended state, it cannot always detect when you add a new USB device to your computer.

RESOLUTION
Windows XP users
Step 1
To resolve this problem, obtain the latest service pack for Windows XP. For additional information, click the following article number to view the article in the Microsoft Knowledge Base:
322389 (http://support.microsoft.com/kb/322389/) How to obtain the latest Windows XP service pack
Step 2
After you apply the latest Windows XP service pack, you can create a new registry entry that prevents an OHCI controller from entering Suspend mode.

Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 (http://support.microsoft.com/kb/322756/) How to back up and restore the registry in Windows

Disable the Selective Suspend feature of the USB hub driver. To do this, follow these steps:
1. Click Start, click Run, type regedit, and then click OK.
2. Locate and then click the following key in the registry: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB
3. On the Edit menu, point to New, and then click DWORD.
4. Type DisableSelectiveSuspend, and then press ENTER.
5. On the Edit menu, click Modify.
6. Type 1, and then click OK.
Note If the DisableSelectiveSuspend registry entry is not present, you must create it. This setting affects all USB host controller drivers in the system.

If the value of the DisableSelectiveSuspend registry entry is set to 1, the Selective Suspend feature is disabled. Additionally, the Allow the computer to turn off this device to save power check box does not appear on the Power Management tab for the USB Root Hub.

Windows Server 2003 users
Create a new registry entry that prevents an OHCI controller from entering Suspend mode.

Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
322756 (http://support.microsoft.com/kb/322756/) How to back up and restore the registry in Windows

Disable the Selective Suspend feature of the USB hub driver. To do this, follow these steps:
1. Click Start, click Run, type regedit, and then click OK.
2. Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB
3. On the Edit menu, point to New, and then click DWORD.
4. Type DisableSelectiveSuspend, and then press ENTER.
5. On the Edit menu, click Modify.
6. Type 1, and then click OK.
Note If the DisableSelectiveSuspend registry entry is not present, you must create this registry subkey. This setting affects all USB host controller drivers in the system.

If the value of the DisableSelectiveSuspend registry entry is set to 1, the Selective Suspend feature is disabled. Additionally, the Allow the computer to turn off this device to save power check box does not appear on the Power Management tab for the USB Root Hub.

STATUS
Microsoft has confirmed that this is a problem in the Microsoft products that are listed in the "Applies to" section. This problem was first corrected in Windows XP Service Pack 1.

Please post back if you have any more problems or questions.
If this info is useful, please mark it helpful. Thanks

This discussion is closed to new replies.