Question Locked

BIOS sees DVD burner, OS sees it as a CD burner--DVD rw is gone

0 helpful
6 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

OS: Win98SE, two optical drives: CD rw and DVD rw.

Everything was working fine until last night when I tried to reinstall INCD on my system. It wouldn't go, because it was missing a loader and something to do with dcom98. --I ran dcom. But it made no diff.

Shut down System.

This morning, "My Computer" shows that I have two CD drives instead of a CD and a DVD.

In the control panel, system, device manager. It lists CD drives and under that heading shows the CD and DVD drives (at least the labels). Properties, say both drives are working.

Nero Info tool shows a CD and DVD burner in the system. ASPI is working. Everything looks normal, there.

But My Computer says, two CD burners.

The DVD burner will not record to DVDs. It will play a DVD that was recorded as data, but gives the capacity of the DVD as being full, when it isn't.

A CDFC burned DVD will not play. The system freezes. It also freezes when I put in blank DVD media, read its properties, then remove it.

I also tried to reflash the firmware NEC 2500A 1.0b. --at the end of the flash, the system crashed. (black screen). But NERO still shows the firmware as being installed, so I think it's ok?

As a fix I unistalled INCD: that didn't help.

I removed both optical drives from the CP|System|Device Manager, and rebooted. -- that didn't help.

Sounds like an OS problem to me, but maybe not--what matters is does anyone have experience or an idea how to fix this?

Oh, the BIOS shows a DVD & CD burner, recognized.

But, right after post, the pre-windows splash screen info, says it has loaded two CD devices. The option to boot into windows from a CD or a DVD, now is boot from a CD.

Any ideas on where to start? Thanks, Bob

6 replies

by toughguy000

My suggestion would be to upgrade, as from personal experience win98 and 95 are probably the hardest to troubleshoot due to the fact that it's running on a 16bit and 32bit environment as the same time. Also it tends to not like CD/DVD burners, One of the reasons why I upgraded in the first place.

Places to start:
*Like with every Win98 install my suggestion would be to Format, yet that probably isn't a viable option here.
*Try with only 1 Burner installed, See if it detected within POST, If not see if it will detect it within Nero. Try with the second drive as well.
*Check and see if there is any missing drivers under the Device manager, sometimes the IRQ's are not automatically set, check those as well. (Will have a yellow "?")
*If it's the DVD Burner that will not detect you may have broken the firmware when you updated, Run out grab a cheap-o DVD drive that you can return same day and see if that will detect.
*Reinstall nero
*Backup files and format.

by stars1234

thanks,
I tried several of the suggestions before posting (I'm a MCSE).
I agree Win98 is difficult, but I'm trying to get information of the HDDs, intact, before moving to 2K or XP or Vista. --if I could just get enough room, I'd make a ghost of this c drive, then put on a backup.

If the firmware is bad, that'd show up when I try the last backup. but darn it, I need the DVD to get enough room for the ghost copy.
Or, I suppose, I can copy to about 14 CDs. ugh.
--the darn thing was working perfectly--why did I try to put on a newer packet writer--when I hardly ever use it anyway?

There weren't any yellow cautions, however, I did see some notes that ASPI wasn't working in certain locations, yet NERO says it's perfect.
Since those problems were there before, I don't think they are effecting the opticals, but my AGP slot.

But who knows? After all, its Windows.

If the drive proves to be good, and I have the firmware solid, the only thing left, if nothing else works is to bite the bullet and reinstall or load on my backup, with trashing the latest info. RATS.

If I have any success, I'll get back to you. I appreciate the answers.

bob

by info

I am having the same problem, at home, and with the computer at work. My computer shows the dvd burner (and dvd player) as a cd unit. I've edited the registry, googled until I'm blue in the face for a fix, did a system restore, nothing works.

Both computers encountered the same problem within a few weeks of each other. Very bizarre. What can I do short of replacing the burners/players? I should add that we are operating Windows XP on both machines.

by joel.godin

Let me know if you find a fix before I do
and I'll do the same.
Thanks

by aortega

I would like to know if you were able to find the cause, I am having the same issue at home?

thanks.

This discussion is closed to new replies.