Discussion Locked

DHCP clients unable to browse

0 helpful
7 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Setup brand new win2k server in test lab to replace production server. Setup DHCP and DNS on this server. Client machine in test can get proper dchp lease, but can't browse to the internet. Thought it was problem with "." root domain, which improved situation but did not solve it. Also, sometimes we have to disable, then reenable the client side nic on server to browse on server..... I've read some articles here with each... routing table has been checked, and we have placed static routes.. but no change as of yet... scenario..

Nic Card that connects to internet router:
3com 3c905
IP address 192.168.1.5 (from internet router static pool)
mask: 255.255.255.0
DFG: 192.168.1.1

Client NIC
Linksys LNE100TX
IP (Static) 10.0.0.1
mask: 255.0.0.0
DFG: none

Any help/advice/comments/suggestions would be appreciated!!!

7 replies

by trackhappy

You haven't given us much to go on. Can you ping the router from the client? Can you ping an IP on the Internet from the client? What are the DNS settings? Using nslookup, can you lookup an IP from the client? Sounds like two problems. One client issue and intermittent connection from the server. Haven't by some chance got a duplicate IP? Does the router know about the cliemt address range? Are there any relevant entries in the event log?..... So many questions, so few answers!

by cg it

Home use DSL/Cable routers are "gateways" for the LAN to access the internet and on statically AND DHCP configured LAN, the router's firmware IP address is supposed to be used as the gateway address for the LAN to reach the internet. The easy way to setup a home network using a router is to have the router dynamically assign IP addresses to the computers connecting to the router. This allows you to leave the NIC properties to "obtain automatically" IP address assignments. Where some confusion with home use DSL/Cable modems is setting up their web browser to work with the DSL Cable modem .

Most home use DSL/Cable modem routers require you to setup your web browser a certain way. Some require all property check boxes to be left blank, [SMC DSL/Cable modem routers are like this] some require you to include the info. The manual that came with the modem will specify how to set up the web browser. Your problem may simply be the web browser isn't setup right to work with the router.

by curlergirl

First, you are correct in turning off the "." root setting in DNS, but you also need to set your ISP's DNS servers as forwarders on your internal DNS server (right click on the server name or zone name - I don't remember which - and you'll see a tablabeled "forwarders", set up your ISP's DNS server IP addresses on this tab). Also, make sure NAT is turned on on the router - if it is one of the low-end broadbrand routers like LinkSys or Netgear, it's probably on by default, but this would be something to check. If it's not on, that would prevent you from browsing. Also, you need to set your client NICs to use the server's 10.0.0.1 IP address as the default gateway, and make sure IP forwarding is enabled on the server. One suggestion to make your life easier, though - turn off the DHCP properties of the router (what you refer to as the "router's static pool" of IP addresses). Give the router a LAN IP address on the same subnet as the rest of your LAN (i.e., 10.0.0.x) and connect it directly to a hub or switch. Again, make sure NAT is on on the router. If your server is running proxy, then set the default gateway on the server to the router's internal IP, and set the default gateway for all your client NICs to the server's (10.0.0.1). If your server isn't running any proxy software, then you need to set all server and client NICs to use the router's internal IP (10.0.0.x) as the default gateway. Hope this helps!

This discussion is closed to new replies.