Question Locked

Is the Laser Printer toner broken or the printer?

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I have an HP LasderJet P2015d that worked fine until the printer either fell 4 feet to the ground, or an extremely large book fell on it (the story from the office varies...).

When I print, it sends a page through the printer which comes out warm to the touch but with absolutely no ink on it. There is a dent in the metal casing when I open the printer and the mechanical pieces *seem* to be in working order so my question is: are toners subject to some sort of internal damage that would keep them from working after a physical shock like this, or is it more likely something inside the printer not working?

I have no other toners to try in the printer

9 replies

by older mycroft

If there's a dent - it came from somewhere.

Where does this feeling come from that a Printer is not observant to evident damage?

If you have damage, find out how it was caused!!

by robo_dev

inside the printer.

If there is toner all over the lens assembly and corona/transfer wire, it is unlikely to print.

A HP toner cartridge consists of a rotating image drum and a bunch of toner. As long as the drum can rotate freely and the gears are not damaged, it is likely a good toner cartridge.

My guess would be that either:

a) toner has spilled
b) something else broke (e.g. laser scanner assembly, circuit board)

if there is a dent in the metal casing, and there is a circuit board right behind the metal casing, then the circuit board is toast.

http://computer.howstuffworks.com/laser-printer.htm

In terms of 'how to lie', your office needs to work on that... dropping an 'extremely large book' on a printer would do nothing at all. Of course I cannot imagine how you drop a laser printer???

by oh smeg

I saw the results of one being allowed to bounce down the stairs taking out a couple of members of the Public and the Office Managers Car. Only good thing about that fiasco was the the idiot who insisted that the printer be moved by the steps get her car damaged quite badly. :D

The members of the Public on the other hand where badly hurt and spent a long time in the hospital which is fairly consistent as they where going to the Health Department when they where attacked by the printer. :^0

Then being a Government Department they didn't have any money in their budget to replace the by now trashed Printer but they had enough money to Repair it at only 3 times the cost of a new one. I'll leave it to you to guess which option that took there but the repair wasn't that great and they now employ someone to stand beside this printer and close the door when it Micro Switch says that the front cover is open. Officially they refill the Laser Printer as required but in reality they are paid to stand there and close the door every so often. :^0

Col

by oh smeg

The most likely thing if it was dropped is that the Transfer Belts are no longer transferring Toner from the Cartridge to the Paper so that the Fusser can not melt it onto the paper when it goes through the Hot part of the printer.

The only real option here is to look at the Service Manual for this unit here to work out what is required

http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01366409/c01366409.pdf

But owing to the confusion here I would say that someone dropped the printer and it's now toast. From past experience with these things they are not worth repairing so look at your Insurance Policy and see if you are covered and then make a claim and replace the printer. ;)

Of course it's also possible that someone dropped it and then someone else dropped a Big Book on it but the Fall tot he Floor is what is most likely to do the damage.

Col

by james

Sounds like it's probably not the toner then. I'm not at all a printer expert, and in fact do all I can to avoid having to deal with them.

I suppose I will order a new one for this office (it's not *my* office). Anyone have any good suggestions in the $400-$600 price range?

by 1bn0

They were trying to remove a Big Book from the top of the cabinet nex to the printer. The book fell and they knocked over the printer trying to prevent the book from falling.

This discussion is closed to new replies.