Discussion Locked

Only my puter on NW Neighbourhood

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Start>Find>Computer won't work with (computer name) nor with \\putername\shared folder
Went through NetworkTroubleShooting Guide..no luck..The Workgroup is correct, the client, adapter, and protocol OK on both. Client for MS Networks is Primary Network Logon - Turn on both puters, Log out, and log back into the Network...passwords OK...still no go...both Win98..All RJ45s in correctly, both to computers and to hub...I'm stumped...Original question was USER DELETED...guess cuz I was not on the database yet...Hopefully this time it's OK...I would really appreciate an answer ASAP...Thanks :)

10 replies

by ann777

Have you turned on "File & printer sharing" and created some shares on both? Check control panel --> Network and click on the "File and Printer sharing" button.

At a DOS prompt, make sure that both computers are in the same network (use winipcfg at the DOS prompt)... 169.254.x.x with a subnet mask of 255.255.0.0.

You might need to install the MS NetBEUI protocol on both bomputers ... unless one is a true server.

The "User Deleted" appears whenever a login id gets messed up and a timeout occurs in the midst of posting a question or responding to a question. Once your id becomes "User Deleted" you need to send an e-mail to TechRepublic to have is corrected (I think...)???

by techno

I retract that...sorry..someone is helping me check...my IP address on one is 209.167.37.xx the subnet mask is 255.255.255.0 the default gateway is 209.167.37.xx (same oas the IP address and the DHCP is 255.255.255.255...And, on the other it has an adapter address, but both the IP address and submask are 0.0.0.0..and no default gateway...It doesn't give me an option to change it in the winipcfg details box...can you let me know what I should do now...step by step? Pinging doesn't work...as it says 'destination host unreachable" Still can't rate yet...sorry as I have to keep open

by techno

File & printer sharing turned on...shares on both puters...worked fine yesterday...protocols are TCPIP..worked...but I'm not too sure (without loads of digging into old notes)how to adjust the IP address and subnet mask on the puter without them...why would this change on it's own? Why work yesterday and not today? I'm stumped!

by techno

Requesting help from work...it's almost at the end of my day...thanks to Anna777 for your input. I'll check in from home this evening for any more suggestions, and rate tomorrow once I try out what has to be done...thanks to all...keep the answers coming :)

by mdelyea

Uninstall all protocols from the network section of control panel. If you will not be sharing the internet connection, only install netbeui. Make sure workgroup is the same on all machines. Turn on your shares (disks, folders, printers). Reboot all computers. Wait about 5 minutes (while network negotiates). You should be able to see each other. If you want to use DHCP and TCP/IP, that is too complicated to explain here.

by techno

We'll be sharing the intenet as soon as I get this up and going so I need the TCP/IP. The workgroups are the same and the shares are open...I've rebooted like you said several times previously...no luck. the winipcfg on the other puter default back to a PPP Adapter which shows IP Address as 0.0.0.0. and SN Mask as 0.0.0.0. with no Default Gateway, etc...when I choose the D-Link DFE-538TX 10/100 Adapter (which it is), then the IP address shows (169.254.41.X and so does the subnet mask (255.255.0.0) and the DHCP is the same as with the PPP Adp (255.255.255.255) These D-Link settings don't hold though...winip...again shows back to the PPP Adapter...My puter is consistent with the D-Link and the IP, SN, Default Gateway, and DHCP. There areonly 2 puters involved connected via the hub...the ip addresses are dynamically assigned (as the lease dates come up)...sorry still can't rate :(

by lyallaust

Since you can see your own computer, it means that you at least have protocols and drivers installed. This means it's a problem communicating across the cables. Two options:
1) The cable is crossover where it should be straight through (check forindicator lights), or something is wrong with the cable.
2) The communication speed is too high. Can be set from withing Network Neighbourhood Properties, under the NIC Properties (eg Intel 100 Adaptor), in Advanced. There is an option usually listed there called "Link Speed" or something similar. Drop this down to 10, and you may want to try "Half-duplex", though this rarely is the issue.

by techno

Both puters can ping themselves, but not each other. The other says Destination Host Unreachable and mine says request timed out.
The hub I use has auto-negotiation which determines the transmission mode or any twisted-pair connection and is not disabled (I used 100BAST-TX UTP CAT 5 with the RJ45 connectors when I made the cable up - I used to make both types up for stores in Vancouver) The Hub indicator lights; Power ON; LINK?ACT on so connected to the stations on both; The 100M indicator ison so the port is connected to a 100M Fast Ethernet station; the FDX/COL lights are on so the ports are in full duplex mode (where they should be)..this is all brand new, and I purposely bought the hub so I could have this transmission - the dealer assures me that it is not the problem (and it did work a couple of days ago without any problems prior since I set it up. We did have a new person on the other puter who wasn't as familiar as she should have been...I asked her to shut down for a bitso I could do something with the Network, and she just hit the power button!!! Don't know what else she was doing for her three days here...anyway..it worked...then it didn't and I'm still stumped....:((( :) Please keep trying OK?

by techno

IT'S FIXED!!! Thanks to you all for your help....I dug out my TCP/IP books and notes...put the two subnet masks to 255.255.255.0 and changed the IP addressess to one number off each other..then did a START>RUN>COMMAND ok IPCONFIG....it was ok...they could then ping each other, and the \\IP Address at the run command found the other puter, soI now have the network up and going. I did phone D-Link and they were a tremendous help. Anyway, thank you all...I really appreciate your efforts.

This discussion is closed to new replies.