Discussion Locked

(RPC) service hangs in starting status

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi, I have a problem which I've received no help from M$ on. Maybe someone here has run into the same problem. I have a workstation with serious mental problems. Here's the sequence of
problems I've experienced. It all strarted when I tried toupgrade the
memory from 32 meg to 160 mb by adding a 128 mb chip. I received the error
"Stop: 0x00000050 (oxff05b040,0x00000000,0x804a1d40,0x00000000)
PAGE_FAULT_IN_NON_PAGED_AREA Address 804a1090 base at 80400000,datestamp
38409b17 - NTOSKRNL.EXE" when win2k starts up. It goes on to mention to try
removing newly installed hardware and whatnot so I do. It works fine with
the original 32mb dimm. I tried 3 other chips with the same outcome. The
chips do work fine in other computers.So I proceed to install SP2 since
its running the base win2k. It doesn't work because the printer spooler is
having problems. I track that down to the RPC service hanging in the
startup mode. My question is what would cause RPC to hang and howwould I
fix it. My last resort is to blow out the hard drive and reinstall win2k
but thats alot of work and if I can avoid it, that would be great. Any
ideas?
Thanks
Pete

5 replies

by curacao_dejavu

From experience: not all motherboards accepts mixed memory.
And even if they say they do it may not work.
If you want to try that make sure you have the same model and same speed (and still may not work.
Use only the 128 MB (check with the Motherboard f course).
I set the spooler service and the rpc on manual. And install a update driver for the printer as the existing on may be corrupted.
Check the ms kb Article ID: Q224370

Success.

Leopold

by p. dickason, cne, mcse, cca

Its not a hardware problem. As I mentioned these dimms work fine in other computers of the same model. The Dimms are specifically for this model of compaq. I did try the 128mb dimm by itself and get the same error. It has to have something to dowith the RPC service hanging for it hangs with the original chip also. I can't do anything with the printers without this service because its a dependency of the print spooler service. And of course SP2 needs the print spooler service to install for god knows why. Thanks for the try tho.

by estebandelatorre

The rpc has some dependencies wich you can explore under the service/depencencies.Another service may have the problem first...
If possible, uninstall SP2, restart and perform a Win2k "R"epair from the cd instalation.
Windows will restore all files to it's original, without having to install all aplications again.
About the memory.
The problem arrise when you install the memory, no?. What I think is that the compaq model may not fully support win2k (I buy Compaq pc's every month, and don't remember quite so well, but 64 is a standart memory size from Compaq, since Nov 1999)
Double check the memory type and allways install the less speed/size memory on BANK=0
Also let the machine performs a memory check by booting the system with the utilities disk.
Another: Some Compaq models maps some available memory to be used in order to extend the video card memory, this may be the problem. Use Setup to disable this function.

by p. dickason, cne, mcse, cca

The repair was my thought too but it didn't work. Must be a hardware problem but since its a p-233, I recommended not to pursue it further. I could have tried reinstalling Win2k but if I spent 3-4 more hours doing that, they pretty much bought a new PC. Even the BIOS was lacking. There was nothing about memory shadowing or caching or whatnot. Just what drive to boot from and BS like that. Oh well, thanks for the help.

This discussion is closed to new replies.