Question Locked

Toshiba M100: Display didn't show nothing.

0 helpful
5 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello all.I need some help.

The problem: My Laptop display didn't show nothing after press ON button.The LED showed as normal.I'd try to overcome this by press ON & OFF the laptop.It take 10 times or more for the laptop to show the display/booting.There is no error showed on booting process, but date & time was changing.

I have did this but it's not work: 1) Uplugged the battery & use the power adapter only.
2) Remove RAM, battery, HDD.

Is that a CMOS battery problem?

Regards

5 replies

by oh smeg

Problems when you turn on the computer

These problems may occur when you turn on the power.

The computer will not start.

Make sure you attached the AC adapter and power cord/cable properly or installed a charged battery.

Press and hold down the power button for a few seconds.

If you are using the AC adapter, check that the wall outlet is working by plugging in another device, such as a lamp.

If Something Goes Wrong

Problems when you turn on the computer
The computer starts but, when you press a key, nothing happens.

You are probably in Standby mode and have a software or resource conflict. When this happens, turning the power on returns you to the problem instead of restarting the system.
To clear the condition, press Ctrl, Alt, and Del simultaneously.

Clearing the condition may get the computer running, but it will not solve a resource conflict. Read the documentation that came with the conflicting device and ?Resolving a
hardware conflict? on page 194.

The computer is not accessing the hard disk or the optional external diskette drive.
Your computer normally loads the operating system from the hard disk. If you have a hard disk problem, you will not be able to start the computer. Insert a system diskette into the optional external diskette drive and press F12 when the machine starts and use the arrow keys to select the boot-up
device.

The computer displays the WARNING RESUME FAILURE message.

The computer was placed in Stand By mode and the battery has discharged. Data stored in the computer?s memory has been lost.

To charge the battery, leave the computer plugged into a live wall outlet for several hours. For more information, see ?Power and the batteries? on page 199.

The computer displays the Non-System disk or disk error message.

Make sure there is no diskette in the optional external diskette drive. If there is one, remove it and press any key to continue.

If pressing any key does not work, press Ctrl, Alt, and Del to restart the computer.

The Complete Toshiba Publications is available here

http://tinyurl.com/6f4nw3

Or you could try plugging in an External Monitor to see if that makes any difference. It is possible that the BIOS was changed to work with the external Monitor or maybe just that the Date is so wrong that the system is having problems trying to work out how to proceed.

You can try entering the BIOS and resetting the Date & Time and [b]save the changes when you exit[/b] or they will not be saved.

Col

by hesgotmail

Hello mate.Thanks for your attention.

I've have try above solution but it's not work.
My battery & AC adapter is working fine.
The problem is my screen unable to show anything signal after pressing ON button.
I means, in my screen there is no show BIOS processing information or TOSHIBA welcome screen.

So, how come to enter the BIOS?Can't access anything either by pressing CTRL+ALT+Del or enter the BIOS.

I've already plug in other monitor to see the input but it was same.

IF the laptop is successfully started(15 times or plus by pressing ON & OFF), but there is another issue.After I reboot/shutdown the laptop is back to the mainly issue.The power is on but can't see the BIOS process/Welcome screen.

I'm also a little bit surprise, why my browser shortcut button(near ON button) also act like a switch.The power is ON after pressing that.

A little help.Thanks & regards.

by oh smeg

All you can do is return the system to Toshiba if it is Under Guarantee for repairs or to your nearest Computer Repairer if it isn't.

There is something wrong inside the unit that may not be easily or cheaply repaired. Or even found for that matter.

What was posted above was a way to try to isolate the simple things. As this didn't work it's now a job for the Professionals. Sorry about that.

Just be sure to Backup the HDD if you have important Data on the Drive by removing it from the NB and fitting to a External USB Caddy then plugging into another computer. You should be able to read your Data From here.

Col

by juergen311

Hi there,
I have exactly the same problem. Only my notebook doesn't want to start after 20 times trying.
Have you found any solution?

thanks

This discussion is closed to new replies.