Question Locked

Can a power supply determine if BIOS starts or not?

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I've been building a computer and replaced practically every component except the power supply. Is it possible BIOS won't start up because my video card needs 400W minimum and my power supply is only 400W?

11 replies

by mjd420nova

If the video card won't start because of not enough power, the BIOS won't start either. The video BIOS has to start first in order to tell the system BIOS where to send that info. You didn't state the CPU type, or video card selection but in some cases 400 watts is not enough. Add in a large memory of over 2GB, and a couple hard drives and 550 watts would be the minimum.

by midgetdoggy

The video card is too. Everything's running fine, lights are all set, but the thing missing is just BIOS starting. When I plug my monitor into my video card the monitor light goes green like it sensed something for a second but then goes to sleep mode. Could it still be low power supply?

by thumbsup2

Are you saying that you can't get into the BIOS and see them on the screen? Can you see anything on the screen? The little green/blue light coming on just means that it senses that it's connected. Doesn't mean the computer is actually starting. I'm confused about what it is that you're saying.

As previously stated though, yes, you're probably under powered.

by midgetdoggy

I put in a PCIe x1 card in there just to determine if it was the video card acting up but still the same. A PCIe x1 card couldn't possibly hog all that power right? And I'm sure it's not my monitor or motherboard.

by mjd420nova

Does the system board have onboard video? If so, connect the monitor to that and see what happens. If you get video there, then enter the BIOS and disable it so it can then use the plugin video card.

by .martin.

you could have my problem if turning off the onboard video doesn't do anything...

if it boots up normally with the onboard video, you turn onboard video off, and you still can not get it to boot, your problem my be dead (or dieing) PCI slots :(. and yes this will effect ANY PCI card, with different results, I had a graphics card not boot 19 out of 20 time, but that one time I would get a BSOD. while I had an IDE Raid PCI card which always booted, but then always crashed between windows loading up and five minutes after windows had finished loading.

as for solution??? new motherboard...

by thechas

First off, I do think that your power supply is too small. I don't even look at power supplies rated for less than 500 watts anymore.

Consider that if you are building up a system with a high power video card, the other components are apt to be power hungry.

That said, if there is a problem with the power supply being loaded down, the health monitor section of the BIOS should be shutting the system down or at least giving a warning.

So, while your power supply is under-rated, it is most likely not why the system does not boot.

Keep in mind however that an under sized power supply is the easiest way to damage the rest of the components of your new system.

As to your no post situation, start by checking the clear CMOS jumper on the motherboard. If that is in the normal position, then:

Disconnect or remove as much hardware as you can. Have no drives, plug-in cards (other than video) and minimum RAM.

If it still does not POST, verify that the CPU fan is plugged into the correct connector. Double check all configuration jumpers on the motherboard. Make sure that ALL motherboard power connections are plugged in. Most modern motherboards use both a 24 pin main power connector and a 4 or 6 pin secondary power connector.
Also check for extra power connectors on your video card.

Still no POST?
Well, try a bigger supply. Check that the CPU is properly seated.
Remove the motherboard from the case and make sure that there are no support posts that could make contact to active circuits.

Still no POST?

Now it's time to find a comparable system and see if the CPU and RAM are any good.

Chas

One more thing, check the line voltage switch on the power supply and make sure it is set for the correct line voltage.

by midgetdoggy

except the only thing I haven't tried to replace yet is the memory. I also haven't tried to clear the CMOS yet seeing as how I don't really know what to do with it and don't wanna mess anything up

by midgetdoggy

twice, actually. Kept thinking it was the problem. But the same thing keeps happening.

This discussion is closed to new replies.