Question Locked

Can C: drive be SCSI, 2nd drive be ATA?

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I'm puttering with an old Comaq Deskpro 2000. It has an Adaptec SCSI
controller with an 18 Gbyte drive attached, configured as C: with XP
loaded.

Can I attach another drive to the primary ATA bus and set it up as a
second drive, other than C:? I would still like to boot from the SCSI disk.

Thanks...just trying to learn, is all...

12 replies

by retro77

you might have to go into your BIOS and tell it that you want the bootable drive to be the SCSI controller, or if that option is not available, remove the ATA HD as a possible boot device.

When you format the new drive, it will not let you choose C:, it'll default to the next available.

by chico_woodhill

Thanks for the reply.

Unfortunately, when I try to boot with the freshly
formatted ATA disk attached, I get a "Disk 0" error.
Perhaps it's a conflict with the SCSI C: drive, but with both
the ATA and SCSI drives attached the system won't boot,
even from floppy.

It looks like I can configure the system to put the SCSI
drive as D: or other, with the ATA drive as C:, but not the
other way around, especially since I can't get the system
to boot from the C: SCSI disk when the ATA drive is
attached...

Any other thoughts for me?

by oh smeg

Sees the ATA Drive? If you haven't that could be the problem.

Col

by oh smeg

If you have you need to set the Boot Order to Floppy, CD or Optical then SCSI and finally IDE. If you don't have any of the above devices just don't worry and forget about setting them in the Boot Order.

You may also have a setting elsewhere in BIOS that asks what to boot from you need to set this to SCSI as well.

Col

by oh smeg

All that should be required is to plug in and mount the ATA Drive. Depending on the BIOS used you may need to going the BIOS and look for the ATA Drive though.

But you need to know that the ATA Drive will be seen by the Hardware as the C Drive as they are always the Default Drive but you can continue to Boot From the SCSI drive which will be seen by the OS as the Boot Drive and the ATA Drive will be seen as the D Drive.

Col

by retro77

I'm wondering if the ATA drive is not formatted fresh. If the drive has a C: partition, maybe the OS is hanging up. Also he's using a Windows 98 floppy. Its been too long since I used one of those to help troubleshoot that portion.

Maybe the Compaq ATA controller requires the correct DOS drivers in order to access taht ATA drive.

by chico_woodhill

I formatted the drive fresh in another machine. Tested out
ok. I can't figure out why having this fresh drive attached to
the ATA bus & the SCSI card pulled won't let the W98 floppy
boot, but it'll boot if the ATA drive is removed...

by chico_woodhill

I can load the compaq diagnostics/setup disk with the
ATA drive attached, and it sees the disk. But for some
reason the system won't boot with my W98 floppy with
the ATA drive attached (it will boot from floppy with the
ATA drive removed).

Maybe there's a problem with the ATA drive and I'm
beating my head against the wrong problem.

by chico_woodhill

I see where I could change the boot order, which I didn't
change.

There is no other setting in the BIOS that I can see that
provides an option to boot from SCSI or anything else. I
only see that I can disable the ability to boot from
removable disk.

Connecting or disconnecting the ATA disk causes the BIOS
to recognize the change, indicate the correct disk size,
and prompt me to save the changes.

Also, at boot time I can enter the SCSI controller card
setup utility, and it lets me set the Boot SCSI ID (which is
0), but of course the SCSI card doesn't see or know about
the ATA disk.

by oh smeg

If you can try in in another computer to see if it works though I think that you will find that it will. Perhaps a look at the Compaq Owners Manual is required here. You can do a search for it from here

http://tinyurl.com/yws9ta

Col

by chico_woodhill

This problem is an interesting challenge, but I've got
several more that I should address first. I thank you for
your suggestions, and I'll pick this one up again when I
get more time. Thankfully it's not necessary that I resolve
it immediately.

I'm always amazed at how complex the problems can be
with these systems that, if they had been designed with
more foresight, should be fairly straightforward.

This discussion is closed to new replies.