To install the cable modem
1.Power down your PC and unplug it from the power source.
2.Connect your PC to either the ETHERNET port or the USB port using the appropriate data cable. Do not connect your PC to both the Ethernet and USB ports at the same time. You can connect two separate PCs to the gateway cable modem at the same time by connecting one PC to the Ethernet port and one PC to the USB port.
3.Connect the active RF coaxial cable to the CABLE connector. Use an optional cable signal splitter to add a TV, a DHCT or set-top converter, or a VCR.
4.Insert the AC power adapter cord into the DC POWER connector on the back of the gateway cable modem, and then plug the power adapter into an AC power source.
5.Plug in and power on your networked devices including your PC. The gateway cable modem will then begin an automatic search to locate and sign on to the broadband data network. This process may take up to 5 minutes. The modem will be ready for use when the CABLE indicator on the front panel stops blinking and illuminates continuously.
6.The next step in setting up your gateway cable modem is to configure your Internet devices for Internet access. Choose one of the following options:
If you want to use Ethernet connections, you must configure the TCP/IP protocol. To configure the TCP/IP protocol, go to How Do I Configure TCP/IP Protocol, next in this guide.
If you want to use USB connections, you must install the USB drivers. To install the USB Drivers for USB go to How Do I Install USB Drivers, later in this guide.
How Do I Configure TCP/IP Protocol?
To configure TCP/IP protocol, you need to have an Ethernet Network Interface Card (NIC) with TCP/IP communications protocol installed on your system. TCP/IP is a communications protocol used to access the Internet. This section contains instructions for configuring TCP/IP on your Internet devices to operate with the cable modem in Microsoft Windows or Macintosh environments.
Configuring TCP/IP on Your Internet Devices
TCP/IP protocol in a Microsoft Windows environment is different for each Microsoft Windows version. Follow the appropriate instructions in this section for your operating system.
To configure Windows 95, 98, 98SE, or ME systems
1.Click Start, select Settings, and choose Control Panel.
2.Double-click the Network icon in the Control Panel window.
3.Read the list of installed network components under the Configuration tab to verify that your PC contains the TCP/IP protocol.
4.Is TCP/IP protocol listed in the installed network components list?
If yes, go to step 7.
If no, click Add, click Protocol, click Add, and then go to step 5.
5.Click Microsoft in the Manufacturers list.
6.Click TCP/IP in the Network Protocols list, and then click OK.
7.Click the TCP/IP Ethernet Adapter protocol, and then choose Properties.
8.Click the IP Address tab, and then select Obtain an IP address automatically.
9.Click the Gateway tab and verify that these fields are empty. If they are not empty, highlight and delete all information from the fields.
0.Click the DNS Configuration tab, and then select Disable DNS.
10.Click OK.
11.Click OK when the system finishes copying the files, and then close all networking windows.
1.Click YES to restart your computer when the System Settings Change dialog box opens. The computer restarts. The TCP/IP protocol is now configured on your PC and your Ethernet devices are ready for use.
12.Try to access the Internet. If you cannot access the Internet, go to Having Difficulty, later in this guide. If you still cannot access the Internet, contact your cable service provider for further assistance.
To configure Windows 2000 systems
1.Click Start, select Settings, and choose Network and Dial-up Connections.
2.Double-click the Local Area Connection icon in the Network and Dial-up Connections window.
3.Click Properties in the Local Area Connection Status window.
4.Click Internet Protocol (TCP/IP) in the Local Area Connection Properties window, and then click Properties.
5.Select both Obtain an IP address automatically and Obtain DNS server address automatically in the Internet Protocol (TCP/IP) Properties window, and then click OK.
6.Click Yes to restart your computer when the Local Network window opens. The computer restarts. The TCP/IP protocol is now configured on your PC and your Ethernet devices are ready for use.
7.Try to access the Internet. If you cannot access the Internet, go to Having Difficulty, later in this guide. If you still cannot access the Internet, contact your cable service provider for further assistance.
To configure Windows XP systems
1.Click Start, select Connect to, and choose Show all connections.
2.Double-click the Local Area Connection icon in the LAN or High-Speed Internet section of the Network Connections window.
3.Click Properties in the Local Area Connection Status window.
4.Click Internet Protocol (TCP/IP), and then click Properties in the Local Area Connection Properties window.
5.Select both Obtain an IP address automatically and Obtain DNS server address automatically in the Internet Protocol (TCP/IP) Properties window, and then click OK.
6.Click Yes to restart your computer when the Local Network window opens. The computer restarts. The TCP/IP protocol is now configured on your PC and your Ethernet devices are ready for use.
7.Try to access the Internet. If you cannot access the Internet, go to Having Difficulty, later in this guide. If you still cannot access the Internet, contact your cable service provider for further assistance.
Frequently Asked Questions
Q. What if I don?t subscribe to cable TV?
A. If cable TV is available in your area, data service may be made available with or without subscribing to cable TV service. Contact your local cable service provider for complete information on cable services, including high-speed Internet access.
Q. How do I arrange for installation?
A. Professional installation from your cable service provider may be provided. A professional installation ensures proper cable connection to the modem and to your PC, and ensures proper configuration of all hardware and software settings. Contact your cable service provider for more information about installation.
Q. How does the WebSTAR Cable Modem connect to my computer?
A. The cable modem connects to the USB port or the 10/1 00BaseT Ethernet port on your PC. If your PC is not equipped with an Ethernet interface, an Ethernet card is available from your local PC or office supply retailer, or from your cable service provider.
Q. After my cable modem is connected, how do I access the Internet?
A. Your local cable service provider becomes your Internet Service Provider (ISP), offering a wide range of services including e-mail, chat, news, and information services. Your cable service provider will provide the software you will need.
Q. Can I watch TV and surf the Internet at the same time?
A. Absolutely! If you subscribe to cable television service, you can watch TV and use your cable modem at the same time by connecting your TV and your cable modem to the cable network using an optional cable signal splitter.
Q. Can I run more than one device on the modem?
A. Yes?a single WebSTAR cable modem will support up to 31 Ethernet devices utilizing a user-supplied Ethernet hub that you can purchase at your local PC or office supply retailer. Another user at your location can simultaneously connect to the USB port on the cable modem. Contact your cable service provider for further assistance.
For more info look at your manual..
Please post back if you have any more problems or questions.