I am using a desktop computer that uses Ubuntu operating system.
I can connect to the internet through just the modem. However when I try connecting through the router I can’t connect to the internet through the Ethernet cable or wirelessly. I am also trying to connect wirelessly to my Playstation 2 and to my Wii. In the future I will have a Playstaion 3 and a laptop computer that I would like to to connect as well. Also in about one month I will most likely have Windows Vista installed on one of my empty hard drives I would like to know if I would have to change anything for that even though I will be unplug that hard drive of the operating system I don’t want to use at the time?
All help is appreciated.
if there are any questions add to this thread or email me at
frozenfire0808@yahoo.com
These are the stats from my modem. Where there are a whole bunch of 1’s that is where the stats of my computer are and where there are a whole bunch of 2’s are the stats from my router the 3’s are where on the
router it actually says stats
PS the stats from my modem are when the router isn’t connected and the Ethernet cable is connected to the computer
It my be long but it is pretty detailed I couldn’t copy and paste everything because it looked messed up in this text box.
under connection summary it said
IP Network Address
PPP 69.179.151.67
Primary DNS 66.112.11.87
Secondary DNS 66.112.11.88
Domain Name myhome.westell.com
under VC Configuration
Status VPI VCI Protocol
enable 8 35 PPPoE
disable 0 36 Bridge
disable 0 37 Bridge
disable 0 38 Bridge
disable 0 39 Bridge
disable 0 41 Bridge
to the right of PPPoE and Bridge is an edit button
when clicking the edit button next to any of the Bridge buttons it says You must enable this VC before editing
when pressing the edit next to PPPoE it says
VC 1 Configuration
VPI 8
VCI 35
PCR 100
QoS UBR with an option to go to CBR or VBR
Protocol PPPoE with an option to go to PPoA Bridge or Classical IpoA
VC 1 – PPPoE Settings
IP Address 0.0.0.0
Gateway 0.0.0.0
DNS Primary 0.0.0.0
DNS Secondary 0.0.0.0
MRU Negotiation has a box that is not checked
LCP Echo Disable has a box that is not checked
LCP Echo Failures 8
“Must be between 1 and 30 inclusive.”
LCP Echo Duration 60
“Must be between 5 and 300 seconds inclusive
and greater or equal to Retry Duration.”
LCP Echo Retry Duration 10
“Must be between 5 and 300 seconds inclusive.”
Tunneling the button that says enable is checked
if I changed it to
VC 1 – PPPoA Settings
everything is the same
if I changed it to
VC 1 – Classical IPoA Settings it would change to
IP Address 0.0.0.0
Subnet Mask 255.255.255.255
DNS Primary 0.0.0.0
DNS Secondary 0.0.0.0
If I changed it to bridge
VC 1 – Bridge Settings
bridge with an option to change it to routed bridge or proxy bridge
Next is DNS Configuration
User Assigned DNS
Domain Name myhome.westell.com with a set button to the right of it
Static Host Assignment
Host Name IP Address
dslrouter 192.168.1.1 with a set button to the right of it PS clicking the set does nothing
deviceweb 192.168.1.1 with a delete button to the right of that I’m not willing click delete until I’m sure everything will be ok
SmartDevice 192.168.1.1 with a delete button to the right of that
a blank space 0.0.0.0 with an add button next to it
Discovered Local Devices
office 192.168.1.20
next is DHCP Configuration
DHCP Server Private LAN with an option of Off
choosing gives me no writing expect an option of Private LAN
Private LAN DHCP Settings
all of the numbers can be changed including the time
DHCP Start Address 192.168.1.20
DHCP End Address 192.168.1.25
DHCP Lease Time : : :
Days 1 Hours 0 Minutes 0 Seconds 0
Private LAN Configuration
Private LAN DHCP Server Enable has a check mark next to it
Private LAN Enable has a check mark next to it
Modem IP Address 192.168.1.1
Subnet Mask 255.255.255.0
Private LAN DHCP Settings
DHCP Start Address 192.168.1.20
DHCP End Address 192.168.1.25
DHCP Lease Time : : :
Days 1 Hours 0 Minutes 0 Seconds 0
with a save button and a reset button on the bottom
Public LAN Configuration
Public LAN DHCP Server Enable doesn’t have check mark next to it
Public LAN Enable doesn’t have check mark next to it
Public LAN IP Address 192.168.1.20
Public LAN Subnet Mask 255.255.255.0
with a save button and a reset button on the bottom
Single Static IP Configuration
Please select which device will share your Single Static IP.
If “User Configured PC” is selected, a local PC must be manually configured to have the Single Static IP address.
WAN IP Address : 69.179.151.67
then there is a box that says
User configured PC
office
below the box it says
Single Static IP is currently disabled.
below that there is a button that says enable
Service Configuration
Current Profile: Default with a new and edit button to the right of it neither of them do anything except changed the name
Service Name Select a Service there are a whole lot of games and things such as America Online, Need for Speed Porsche, Yahoo messenger chat etc.
with * ‘ Denotes Custom Service below it and buttons to the right of that say enable delete and edit
UPNP Enable the box isn’t checked
Service Name Service Mode Host Device
IPSEC ALG Client Dynamic
with a detail and delete button to the right of it
clicking the detail button says
Service Details
Service Name IPSEC ALG
Type Port Forwarding
Port 1
Protocol: TCP/UDP
Global Port(s): 500
Base Host Port: 500
Port 2
Protocol: TCP/UDP
Global Port(s): 500Base Host Port: 500
Base Host Port: 500
with a close button below it
* If your firewall is enabled, the firewall rules take precedence over the Services.
below that is a button that says define custom service
when I click that it says
Custom Service
Set Up a Port Forwarding entry based on your specific ports
Port Forwarding
Ranges of Ports Forward a range of WAN ports to an IP address on the LAN
Trigger Ports
Forward a range of ports to an IP
address on the LAN only after
specific outbound traffic
with an option to choose Port Forwarding or Trigger Ports right now it is on Port Forwarding
Below the the define custom service but is another button that says Static NAT
when clicking it says
Set Up an IP Address to be your Default NAT Destination.
Static NAT Device office
or specify
IP Address a blank box
All unsolicited inbound traffic will be sent
to the above device.
Note: Static Nat and IP Passthrough are
mutually exclusive features.
with an enable disable and cancel button below it
Firewall Configuration
it is set on low
Remote Logging
enable the box next to it is not checked
Remote IP Address: 192.168.1.20
with a save button below it
ATM Loopback
Enable ATM 0/21 Loopback with a check mark next to it
below that is a save and a reset button
Turbo TCP
Turbo TCP Enable with a check mark next to it
below that is a save button
Remote Access
User Name admin
Password
Timeout 20 Minutes
Disable Timeout the box next to it is not checked
Enable Remote Access the box next to it is not checked
Remote URL: http://69.179.151.67:2420/
Transceiver Statistics
Transceiver Revision: 5.2.2.0
Vendor ID Code: 4
Line Mode: G.DMT Mode
Data Path: Fast
Transceiver Information Down Stream Path Up Stream Path
DSL Speed (Kbits/Sec) 1792 320
Margin (dB) 19.0 23.0
Line Attenuation (dB) 51.5 31.0
Transmit Power (dBm) 16.6 11.5
LAN Statistics
Devices On LAN
IP Address MAC Address Name Status
192.168.1.20 00:13:d4:79:e2:d1 office active
111111111111111111111111111111111111111111111111
111111111111111111111111111111111111111111111111
111111111111111111111111111111111111111111111111
111111111111111111111111111111111111111111111111
On the Screen of my computer
where the two computers are to show internet connection information it says
interface Ethernet (eth0)
Speed 100 Mb/s
Driver skge
IP Address 192.168.1.20
Broadcast Address 255.255.255.255
Subnet Mask 255.255.255.0
Default Route 192.168.1.1
Primary DNS 192.168.1.1
Secondary DNS 192.168.1.1
Hardware Address 00:13:D4:79:E2:D1
2222222222222222222222222222222222222222222222222
2222222222222222222222222222222222222222222222222
2222222222222222222222222222222222222222222222222
2222222222222222222222222222222222222222222222222
2222222222222222222222222222222222222222222222222
Router information
(so much for the easy part)
Basic Setup
Internet Setup
Internet Connection Type
Automatic Configuration – DHCP with an option to use Static IP PPPoE PPTP L2TP Telstra Cable
If possible I want to use DHCP
Optional Settings
(required by some ISPs)
Router Name: WRT54G (original name)
Host Name: empty box
Domain Name: myhome.westell.com (I put this in it was originally blank)
MTU auto
Network Setup
here are all of the words said on the far right verticle collom so I can just copy and paste them all
Automatic Configuration – DHCP: This setting is most commonly used by Cable operators.
Host Name: Enter the host name provided by your ISP.
Domain Name: Enter the domain name provided by your ISP.
More…
Local IP Address: This is the address of the router.
Subnet Mask: This is the subnet mask of the router.
DHCP Server: Allows the router to manage your IP addresses.
Starting IP Address: The address you would like to start with.
Maximum number of DHCP Users: You may limit the number of addresses your router hands out.
More…
Time Setting: Choose the time zone you are in. The router can also adjust automatically for daylight savings time.
Router IP
Local IP Address: 192.168.1.21
Subnet Mask 255.255.255.0
(I assumed it was the same as the modem)
Network Address
Server Settings (DHCP)
DHCP Server: Enable Disable the button next enable is clicked
Starting IP Address: 192.168.1.20 the last digits are the only numbers I’m able to change
Maximum Number of DHCP Users: 5
Client Lease Time: 0 minutes (0 means one day)
any of the following address could be wrong but I got them from the modem
Static DNS 1: 72.141.61.78
Static DNS 2: 66.112.11.87
Static DNS 3: 66.112.11.88
WINS: 0.0.0.0
(I didn’t see the word WINS so I left it blank)
at the bottom there is a save button
Advanced Routing
(this is isn’t the closest of the 3 other tabs in setup but I thought it would be easier to do this one next)
here are the words shown on the far right side
Operating Mode: If the router is hosting your Internet connection, select Gateway mode. If another router exists on your network, select Router mode.
Select Set Number: This is the unique route number, you may set up to 20 routes.
Route Name: Enter the name you would like to assign to this route.
Destination LAN IP: This is the remote host to which you would like to assign the static route.
Subnet Mask: Determines the host and the network portion.
More…
on the far left side is says
Advanced Routing
Operating Mode
with a choice of Gateway or Router
right now it is on Gateway
below that and on the far left side it says
Static Routing
Select set number: 5
to the right of that is a button that says Delete This Entry
Enter Route Name I left a blank box
this is where I have Trouble
Destination LAN IP: 192.168.1.20 .
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.21
Interface: LAN & Wireless with an option of WAN (internet)
right now it is on LAN & Wireless but I have tried them both but when I click the save button on the very bottom is says
May be default route already exists
just below the the LAN & Wireless and WAN option is a button that says
show routing table
when I click it is say
Routing Table Entry List
Destination LAN IP
0.0.0.0
192.168.1.0
Subnet Mask
0.0.0.0
255.255.255.0
Gateway
192.168.1.1
192.168.1.21
this is on the right of the other three
Interface
LAN & Wireless
LAN & Wireless
(none of the numbers have changed so far when messing with numbers before the routing table)
when I change the operating mode to router all of the information is the same
DDNS
On the far right it says
DDNS Service: DDNS allows you to access your network using domain names instead of IP addresses. The service manages changing IP address and updates your domain information dynamically. You must sign up for service through TZO.com or DynDNS.org.
More…
Right now my DDNS is not enabled
MAC Clone
On the far right it says
MAC Address Clone: Some ISP will require you to register your MAC address. If you do not wish to re-register your MAC address, you can have the router clone the MAC address that is registered with your ISP.
More…
I clicked enable and Clone your PC’s Mac
Wireless
Wireless Network
Wireless Network Mode: Mixed with on option of disable, B-Only , and G-Only
Wireless Network Name (SSID): 0808
(from my Wii I can see this wireless network name and I can connect to it but I can’t connect to the internet from it)
Wireless Channel: 11-2.462GHz there are other channels but the Wii can connect to them too just not the internet)
Wireless SSID Broadcast: Enable
with an option to disable
Wireless Security
Security Mode: Disabled
(I’m going to change that after I can get an internet connection)
Wireless MAC Filter
Wireless MAC Filter: Disabled
Advanced Wireless
Authentication Type: Auto with a choice of shared key
Basic Rate: Default with a choice of 1-2Mbps or All
Transmission Rate: Auto with a choice of 1Mbps through 54Mbps
CTS Protection Mode Disable with a choice of Auto
Frame Burst: Disable with a choice of enable
Beacon Interval: 100
(Default: 100,Milliseconds, Range: 1 – 65535)
DTIM Interval: 1
(Default: 1, Range: 1 – 255)
Fragmentation Threshold: 2346
(Default:2346, Range: 256 – 2346)
RTS Threshold: 2347
(Default:2347, Range: 0 – 2347)
AP Isolation: Off
(Default: Off)
Secure Easy Setup: Enable
(Default: Enable)
Security
Firewall
Block WAN Requests
(both of those were on the far left side)
The following have unchecked boxes beside them
Block Anonymous Internet Requests
Filter Multicast
Filter Internet NAT Redirection
Filter IDENT(Port 113)
VPN Passthrough
this is on the far right side
You may choose to enable PPTP, L2TP of IPSec passthrough to allow your network devices to communicate via VPN.
More…
the following are enabled with the option to disable
IPSec Passthrough:
PPTP Passthrough:
L2TP Passthrough:
Internet Access
basicly it says what days I am allowed to use the internet which I choose all the time
on the right side it says
Blocked Services: You may choose to block access to certain services. Click Add/Edit Services to modify these settings.
Website Blocking by URL: You can block access to certain websites by entering their URL.
Website Blocking by Keyword: You can block access to certain website by the keywords contained in their webpage..
there is nothing in any of those spaces
Applications
& Gaming
Port Range Forward is on the far left side and the following is on the far right side
Port Range Forwarding: Certain applications may require to open specific ports in order for it to function correctly. Examples of these applications include servers and certain online games. When a request for a certain port comes in from the Internet, the router will route the data to the computer you specify. Due to security concerns, you may want to limit port forwarding to only those ports you are using, and uncheck the Enable checkbox after you are finished.
More…
In the middle is a chart I will fill out only one line out of the ten because they are all the same
Port Range
Application Start End Protocol IP
Address Enable
0 to 0 both 192.168.1.0
with an enable box to the right of the IP
where the application address is it is blank
where the protocol is there is an option of
TCP , UDP , and Both
where the IP is where the 0 is, that is the only spot available to change
none of the enable boxes are checked
Port Triggering
the following is on the far right
Port Triggering:
Application Enter the application name of the trigger. Triggered Range For each application, list the triggered port number range. Check with the Internet application documentation for the port number(s) needed.Start Port Enter the starting port number of the Triggered Range. End Port Enter the ending port number of the Triggered Range. Forwarded Range For each application, list the forwarded port number range. Check with the Internet application documentation for the port number(s) needed. Start Port Enter the starting port number of the Forwarded Range. End Port Enter the ending port number of the Forwarded Range.
the following is another chart there are again ten places but the are all the same
where the application is it is blank
where the numbers should be there is only a 0
the enable boxes are not checked
Triggered Range Forwarded Range
Application Start Port to End Port start port to end port enable
DMZ
the following is on the far right
DMZ: Enabling this option will expose your router to the Internet. All ports will be accessible from the Internet
More…
there is an enable button checked with an option to choose disable
DMZ Host IP Address: 192.168.1.1
with only the last digit able to be changed
QoS
the following is on the far right side
Two types of Quality of Service features are available, Wired QoS which controls devices plugged in to the router with a Ethernet cable, and Wireless QoS, which control devices that are wirelessly connected to the router.
Wired QoS
Device Priority : You may specify priority for all traffic from a device on your network by giving the device a Device Name, specifying priority and entering its MAC address.
Ethernet Port Priority : You may control your data rate according to which physical LAN port your device is plugged into. You may assign High or Low priority to data traffic from devices connected on LAN ports 1 through 4.
Application Priority : You may control your data rate with respect to the application that is consuming bandwidth. Check Optimize Gaming Applications to automatically allow common game application ports to have a higher priority. You may customize up to eight applications by entering the port number they use.
Wireless QoS
Wireless QoS is also referred to as Wi-Fi MultiMediaTM (WMM) by the Wi-Fi AllianceTM. Select Enable to utilize WMM if you are using other wireless devices that are also WMM certified.
No Acknowledgement : Enable this option if you would like to disable acknowledgement. If this option is enabled, the router will not re-send data if an error occurs.
Upstream Bandwidth Auto with an option of Manual
the Kbps is 0 but I am not able to changed it unless I change the disable button to enable
the Enable button is not checked the disable button is checked
Administration
Local Router Access my password is in black circles
Web Access
Access Server: HTTP HTTPS
both have a check mark by them
Wireless Access Web: Enable Disable
enable has a check mark next to it
Remote Router Access
Remote Management: Enable Disable
disable has a check mark next to it
UPnP: Enable Disable
enable has a check mark next to it
this was on the far right I skipped obvious information
UPnP: Used by certain programs to automatically open ports for communication.
More…
Log: Enable Disable
enable has a check mark by it
on the bottom there are two buttons
one says Incoming Log and the other says
Outgoing Log
Ping Parameters there is a button that says
Ping
Traceroute Parameters there is a button that says Traceroute
Restore Factory Defaults: Yes No
right now there is a check mark next to no
I will reset the factory defaults if it will be easier to explain how to fix my problem
333333333333333333333333333333333333333333333333333
333333333333333333333333333333333333333333333333333
333333333333333333333333333333333333333333333333333
333333333333333333333333333333333333333333333333333
Status
Router Information
Firmware Version: v1.00.9, May.12,2006
Current Time: Not Available
MAC Address:00:13:D4:79:E2:D1
Router Name: WRT54G
Host Name:
Domain Name: myhome.westell.com
Internet
Configuration Type
Login Type: Automatic Configuration – DHCP
IP Address: 192.168.1.20
Subnet Mask: 255.255.255.0
Default Gateway: 0.0.0.0
DNS 1: 66.112.11.87
DNS 2: 66.112.11.88
DNS 3:
MTU: 1500
there is a DHCP Release button and a
DHCP Renew button at the bottom
Local Network
MAC Address: 00:18:F8:EE:78:E1
IP Address: 192.168.1.21
Subnet Mask: 255.255.255.0
DHCP Server: Enable
Start IP Address: 192.168.1.20
End IP Address: 192.168.1.23
there is a DHCP Clients Table at the botton of the screen when I click on it it says
DHCP Active IP Table
DHCP Server IP Address: 192.168.1.21
Client Host Name IP Address MAC Address
Wii 192.168.1.22 00:22:aa:19:a9:10
office 192.168.1.20 00:13:d4:79:e2:d1
It only had the office part at first but then I went into my room and turned on my Wii and hit refresh
Wireless
MAC Address: 00:18:F8:EE:78:E3
Mode: Mixed 11/54Mbps
SSID: 0808
DHCP Server: Enable
Channel: 11
Encryption Function: Disable
