Question Locked

Dual external displays with Toshiba Tecra A8 laptop & docking station

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hello,
I wish to use 2 external LG 19" LCD screens, with my Toshiba Tecra A8 laptop, when it is connected to its docking station (or Advanced Port Replicator III Plus, as Toshiba call it).
I cannot seem to get thsi to work, but I have been told by an associate that it definitely can, at least on the Dell laptops that they use. The docking station has a DVI output and a VGA output.
I can get either one of the external screens to work individually, but not both together.
I want them set up as 'extended desktop', not duplicate. I will therefore not use the laptop screen at all, when in the docking station (as it would be closed).
The laptop has an NVidia Quadro NVS 110M graphics card in it.
Can anyone advise me how to make it work with the two external LCD screens?
Thanks, Wayne

10 replies

by mylittlemansanidiot

If it's at all possible, the settings will be in your Display Properties on the Settings tab. Check this once you have the laptop plugged into the dock, with the two monitors connected to the dock. See if it gives you the option for multiple displays. It would be my guess you can either use the DVI or the SVGA connector, not both, and the laptop's LCD.

by cg it

The NVidia control panel should be in Windows Control panel. you use the NVidia control panel to setup single, clone or dual displays. hook up both displays to the card, then run the NVidia Control Panel to configure the type of dual displays you want.

Note: clone means what is on the primary is on the secondary. great for demo stuff. Dual displays means the desktop is extended to both displays. if you drag a window to the left or right edge of the primary, the window will be seen in the secondary display. This is great if you do a lot of web based stuff. you can work on the primary display using a word processor and on the secondary have the browser there and browse the internet [or have the stock reports showing.

by wneilson

Thanks guys for the feedback and help.
I can go into the Display Properties window, and navigate to the NVidia Quadro NVS 110M properties, and select the 2 external displays which are appearing, but the second screen doesnt light up - just stays dark. Its def powered on, and has the VGA cable from it to the back of the docking station.

Any suggestions?

Regards, Wayne

by jamesmondtan

Press and hold "Fn" then press "display" button (F5) few times to choose the display.

by wneilson

Hello, and thank you to all for feedback and support.
Just to clarify, I can toggle between standard display options using the Fn and F5 keys, but this is not the issue.
I dont want to toggle between the laptop screen and one external LCD screen. I want to be able to view my desktop on two external LCD screens, and toggle between them, when the laptop is in the docking station.
Hope this helps with an answer...
Cheers - Wayne

by cg it

you should see this option in the left pane.
both LCDs should be shown. in the right pane you should have "Choose NView mode" and it will give you the options for single, clone or dual. both LCDs should be listed.

if your second display is not getting a signal then it's the docking station and/or the laptop capabilities. The docking station has to act as a signal splitter if your laptop only has one external graphics port e.g. one VGA or one DVI but not both. if your laptop has both external ports, the docking bay also needs to have connections between the laptop and dock station for both.

you might try turning the one monitor that doesn't have a signal off then back on but that monitor still doesn't have a signal, then it's the laptop or dockstation that's the problem.

also IF your laptop has both DVI and VGA external ports, connect the LCDs to them without the dock station, run the NVidia control panel to setup dual monitors. once you have this configured and it works, it should work with the dock station. Thenyou can create a hardware profile for docked that will keep this configuration. log on using this profile for dual monitor support.

by jamesmondtan

I have done one toshiba A8 notebook on 3 lcd screen. But my case is using 2 docking station.
Notebook to 1st docking station, and from 1st docking station to 2nd docking station then to three lcd monitors.
I realise the 1st docking station looks different, sound's like a type of spliter.
And it works find here, only use "Fn" + display button to toggle it.

by wneilson

Thanks James,
Can you elaborate a bit for me on how you joined the two docking stations together? What type of cabling did you use, and to what ports? I'm interested in this solution.
Thanks - Wayne

by jamesmondtan

I not really know what name should call on the cable ( cause is left over by the previous it person).
Is one vga head, another side is same but with extra ps2 port.(this cable connect from notebook to docking 1.)
use one normal vga cable from docking 1 to docking2.
did your problem solve ?

This discussion is closed to new replies.