Discussion Locked

Dual Monitor

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
If at all possible, how do I configure dual monitors to run on a Gateway box with Windows NT4.0. I have two seperate diplay cards (ATI)installed.

13 replies

by aaron_wurthmann

I'm pretty sure that Windows NT didn't support a dual monitor config, Or if it did it was dependant on your version of Internet Explorer, something crazy and hard to believe like that. Windows 2000 does of course. I would suggest reinstalling the cards, check to see if the both work by themselves. Pull one out, put it back in etc... Then check out the IE tip, I think that it was specific to Internet Explorer 4.01 with Active Desktop. If you already installed IE 5 and skipped over IE 4 that is going to be an issue. Then again, it has been over a year and half since I have been on a Windows NT machine, so it is possible that I am completly out of my mind and that the only time that you can get two monitors is when you have a laptop a monitorand a single graphics card that supports it.

Good luck,
AW

by rcc

Windows NT4 does not support dual monitors. It is only supported on win98, me and 2k.
Regards,
Radu

by nicholasp

With NT4 you can by a separate Card to support multiple monitors. I use the Colorgraphic Communications Corporation Evolution 4 card. It is great, I can hace up to 4 monitors

by william jay

6. How do I enable DualHead under Windows NT

- In the Matrox Display properties (4.1x drivers), go to the performance tab and check the last "check-box" which should read "Use Secondary Controller as Windows Monitor" (for newer drivers you will find a Dual Head tab where you will need to select Multi Display). Both monitors will need to be plugged in for this to work.

- Then go to the Settings tab and select the two monitors? icon on the left-hand column. You should be able to move the slider for the resolution in order to get a virtual desktop value such as 2048x768 (which is actually 1024x768 X2). NT will only allow you to use a virtual desktop and not 2 different resolutions for both screens. If you apply these settings, both monitors should light up. Please note that dragging the resolution slider will show you an image at the top of how the monitors are configured.

7. How do I configure my monitors to get multi monitor support under Windows NT 4? (top)

- In the Matrox Display properties you should have a dual monitor button available in the General tab (last one in the left-hand column). If you can select it, then both cards are detected and you are ready to change your resolution. If you can't select the dual monitor button because it is grayed out, please see this FAQ.

- Select the two monitors? icon on the left-hand column. You should be able to move the slider for the resolution in order to get a virtual desktop value such as 2048x768 (which is actually 1024x768 X2). NT will only allow you to use a virtual desktop and not 2 different resolutions for both screens. If you apply these settings, both monitors should light up. Please note that dragging the resolution slider will show you an image at the top of how the monitors are configured ...

by william jay

Snippet from ATI
---------------------
Does ATI support multiple displays in NT 4.0?
ATI Technical Support has fielded a number of requests which relate to multiple monitor support for Windows NT 4.0.

Common questions are:

Does NT 4.0 support multiple monitors?

or

Company XYZ has a product that supports multiple displays in NT 4.0, does ATI have a similar product?

Currently ATI does not have a product that supports multiple displays in the NT 4.0 environment. It is our understanding that NT 4.0 does not currently incorporate native support for multiple displays. However there do seem to be display products available in the market place that are capable of supporting multiple displays. These products typically have two or more complete display controllers on one card and obviously require special drivers.
-----------------------------------

What do you do if the OS lacks support for a device? Buy a device that supports the OS ...

This discussion is closed to new replies.