Question Locked

DVD and CDROM not Recognized No power for CD-ROM

0 helpful
4 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

After instilling a diver for my firmware my CD-Rom stop working and it has no power. My "E/DVD" has power still but it and my CD-Rom drive are not showing up under Device Manager. The power cable is fine I hook it up to the "E" and it still had power.I am thinking it just died but don't get why it and my "E" are gone off my device manager. Under Bios it says not instilled. No clue what to do.

System Info

0 4X388 INSTRUCTION..., PREP-MTL, DEVIATION..., DIMENSION..., INCREASE..., NUMBER...
1 C1431 PROCESSOR..., 80532, 2.8G, 512K, 533, SOCKET N..., DECISION ONE...
1 7N242 KEYBOARD..., 104, UNITED STATES..., SILITEK..., LOW COST..., MIDNIGHT GRAY...
1 W1668 KIT..., MOUSE..., PERSONAL SYSTEM 2..., 2BTN, WHEEL..., LOGITECH...
2 8T915 DUAL IN-LINE MEMORY MODULE..., 512, 333M, 32X64, 8K, 184
1 H2442 DIGITAL VIDEO DISK DRIVE..., 17G, 16X, I, 5.25" FORM FACTOR..., LITEON..., MIDNIGHT GRAY..., V5
1 4U829 MODEM..., V92, INTERNAL..., DATA FAX..., SOFT, DON JULIO..., AMF
1 7E840 KIT..., SPEAKER..., 120V, HK395, SAMSUNG..., DELL AMERICAS ORGANIZATION...
1 P0151 DISPLAY..., CATHODE-RAY TUBE..., 17, DUAL..., E773C, MIDNIGHT GRAY..., DELL AMERICAS ORGANIZATION...
1 X2603 CARD (CIRCUIT)..., GRAPHICS..., 128MB, R350, PROFESSIONAL..., DIMENSION...
1 2K221 HARD DRIVE..., 80G, I, 3.5" FORM FACTOR..., 1N, 7.2K, WD-XL40
1 M1210 ASSEMBLY..., FLOPPY DRIVE..., 212, 2
1 J1894 KIT..., SOFTWARE..., WP-PRDCT-STE11, ENGLAND/ENGLISH...
1 N2999 KIT..., SOFTWARE..., MNY-2K4, STANDARD..., ORIGINAL EQUIPMENT MFGR...., ENGLAND/ENGLISH...
1 P2643 KIT..., SOFTWARE..., MSENC-2K4, ORIGINAL EQUIPMENT MFGR...., ENGLAND/ENGLISH...
1 R2553 KIT..., SOFTWARE..., OVERPACK..., WXPHSP1A, COMPACT DISKETTE W/DOCUMENTATION..., ENGLAND/ENGLISH...
1 G0766 CARD (CIRCUIT)..., NETWORK..., PC INTERFACE..., BROADCOM CORPORATION..., GIGABIT..., DIMENSION...
1 G2876 KIT..., DOCUMENTATON ON FLOPPY DISK..., SOFTWARE..., CYBERLINK..., 4.14, DIMENSION...
1 P1144 COMPACT DISK READ WRITE..., 680M, IDE (INTEGRATED DRIVE ELECTRONICS) ..., 5.25" FORM FACTOR..., 48X32, HITACHI LG DATA STORAGE..., MIDNIGHT GR

4 replies

by mjd420nova

Somehow when you installed the drivers, they got loaded wrong or are in conflict with another device. The front panel on both the CD and DVD drives have a tiny hole that is the manual eject button. If you stick a paper clip in the hole it should eject the tray. If it doesn't work, then the power is bad, otherwise it's just a driver fault.

by sdogg86

It does pop out with the paper clip. The E/burner still has power but it and the CD-Rom does not show up on the Device Manager. The whole "DVD/CD-ROM drives" are just gone. Will reinstilling the divers fix this? Do I have to replace the "E" drives too?

Thx you for the help

by oh smeg

I think that is the one that is dead to all intents & Purposes so try disconnecting it and reboot the unit and see if the DVD Drive now works.

Sometimes when a Optical Drive dies it can adversely affect anything else on the same IDE Channel so if you disconnect the drive not working at all and reboot you can see if the other one works. Then if it does shut down disconnect the DVD Drive & reconnect the CD Drive and reboot. See if it works now. If it does can you list what you actually installed to this unit and what OS is being used here?

Col

This discussion is closed to new replies.