Question Locked

how to reconnect wires to power button

0 helpful
17 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I was installing some hardware & cleaning up my sister's custom-made/generic desktop PC and accidentally disconnected the wires leading from the power & reset buttons on the front panel to the motherboard.
I THINK I finally figured out the connection order of the wires; however, the 2 wires leading to the power button, one white-one black, was pulled out.
So now I totally am lost on how to re-connect the power wires. I've tried connecting once and nothing- problem is I don't know if I messed up on the wires connecting to the motherboard or the power wires.
The description of the wide wire that runs from the front panel to the motherboard: it is made up of 8 wires that are divided into groups of two. Wires are labeled
1st group: white& black ? labeled ?POWER SW?
2nd group: white& orange ? labeled ?RESET SW?
3rd group: white& yellow ? labeled ?H.D.D. LED?
Then a single white wire ?not labeled
The last wire - a single green wire ?not labeled

The motherboard is: K7SOM+ motherboard

Any help would be greatly appreciated!!

17 replies

by oh smeg

They can go on either connector. You [b]CAN NOT[/b] connect then the wrong way when you have the correct pins.

The same is true for the Reset Button as well.

Col

by thechas

Most of the connectors for the front panel signals latch the pins into the sockets. It can take a lot of force to pull a wire out without releasing the latch.

The first question is do the wires lock into the connector? Or, do they pop out when you seat the connector?

If they pop out, you need to fix the latch on the terminal or the connector body.

If the wires do seat properly in the connector, then, there is a good chance that you fractured a wire.

You can use an ohm-meter or a test light to check the power button circuit.

Connect the meter leads to the switch leads, and press the switch.
When you are holding the power button, an ohm-meter should read near zero ohms. A test light should light.

If the wires are broken, you have several options.

The simple option is to use the reset switch for the power switch.

The next easiest is to find an identical case and swap out the front panel switches and indicators.

The more involved option is to find another power switch and solder the leads from that switch onto the switch in your case.

Note: This would NOT be a good first electronic soldering project.

You might also check around the local PC repair shops and see if they can check and repair the wires for you.

Chas

by jc1194

Thanks fargonebeautiesmate, OH Smeg, & TheChas
for your help!! I'm using your advice...will let you know what happens. : ) Jen

by wallasim

I think that the 1st group is only the power led. i can check for you if u didn't solve it until now

by jc1194

Thanks for replying to my question! I appreciate it!!

I am still having problems... I do have some pictures of the wires and the connections that I know will explain so much better than I could describe.
If you are still interested and have the time to spare... I could send the pics to you or post them ____??? (I'm not sure where u post pics for public access?)

I would be grateful for any assistance.
Thanks!
Jen

by jc1194

I know my 1st post was very confusing and I'm sure hard to follow! So I really appreciate everyone who replied with suggestions.

Same problem - just condensed...
The problem I started out with was connecting the wires to the motherboard. I finally did find the manual but still not sure the wires are in correct order & facing the right direction. In the meantime, I somehow pulled the wires loose from the power button on the inside of the front face plate. With the advice I have received, I have cautiously tried various connections with no success BUT I don't know which area I am messing up - the order & direction of the wires connecting to the mobo or the wires connecting to the power button. This is my main problem!!-if I knew that the mobo wires were correct then even I could solve the power button connections. (after a few rounds of trial & error)
As you can tell...I am losing my mind & pulling my hair out and soooo tempted to throw this computer out the window!!

If interested... I have pictures of the wires and the connections that will explain so much better than I can describe ... I will send the pics to you or post them ____??? (I'm not sure where u post pics for public access?)

I am grateful for any advice or info that anyone has to offer. : )

Thanks!
Jen

by oh smeg

So you could use the Reset Button to Switch On the Computer if the connection at the M'Board end supports this option.

If you would like to send me a Peer Mail with your problem I'll see what I can do to help you out. That is the Blue Writing below my Alias that says Send Message or some such thing.

But just an Idea here if you post the Make & Model of the M'Board I or others here can post the URL of a PDF file of the manual for this unit which has the Front Panel Connection in it.

As far as orientation goes only the LED are Polarised and have to be fitted a certain way any switches can be connected either way and not adversely impact on operation.

Col

by rob miners

Here is a better view of the SW1 Connector. With the case open and you are looking down on the motherboard at the Switch you will notice that pin 10 does not exist that should tell you which direction the pins run. Pin 1 is normally at the back of the board. If the Power Switch is broken just connect the Reset Switch to the Power instead.

http://www.premiopc.com/images/support/front_panel2.jpg

by barkly54

that photo was a life savor. i took the wires out thinking about putting my system in another case like most that know but dont keep track of how your wires go. i took them out without looking to see how they where configured! i could not use my computer for about 1 month 1/2 because i could not rehook the wires the right way !!! bless you my friend i was stuck on a old p.ll 400 mhz to all that have a connection problem with your hd-led h power led power sw reset sw for your k7-som+ plz look for fargonebeautiesmate post of 11/07 that will help you out much

by thechas

At this point, considering that the wires have been stressed, you need to test the wires and connections before going any further.

For the reset and power switches all you need is the ohms mode of a decent multi-meter.

Stick the end of a small paper clip into each terminal of the switch connection and connect the meter to each wire. If it is hard to insert the paper clip, you need a smaller diameter wire. Do NOT FORCE any wire into the socket.

With the switch open, the meter should read over-range, or an open circuit.
When you press the button on the switch, the meter should read near zero ohms. For most switches, less than 10 ohms is a good reading.

Testing the LEDs is more involved. Some meters have enough voltage when in diode test mode to turn on an LED. Most do not.

If the meter can test LEDs, the LED should light up dimly when connected to the meter in one direction, and not light up when connected the other way.

To be brutally honest, if the above instructions are beyond your skills, I recommend that you take this into a local shop and have them take a look at it.

Another alternative is a vocational tech center or community college that offers computer training.

Chas

by oh smeg

I use Sewing Machine Needles to push into these connectors as they are small enough to fit and make contact but not big enough to bend the contacts. I find that they work much better than Paper Clips.

Col

by thechas

Needles is a good idea. Just don't poke yourself.

I normally use header strips or mating pins myself. But, most people don't have these.

Although, you could pick up a header at a Radio Shack.

Chas

by thechas

I actually seldom go to Radio Shack. For many items, I have a better stock than they have anyhow.

While I agree that replacing the entire front panel switch and indicator assembly might be required, at this point, we do not know that the switch or wire is bad.

While I can usually find switches and indicators that will work with a case, I cannot point this peer to a specific new switch (with wires) for their case.

I also believe that this peer wants to verify that the switch or wires are bad before taking any further action.

Chas

by thevirtualone

your answer to this question was not in any way being challenged. I just think that there are certain types of people in this world. Those that take apart their calculator watches, and those who won't.

I would not. ever. it just doesn't interest me. I however would read the schematic on it and find it very interesting. I am also the sort who would find an insurance policy fascinating too.

With that said. You sir are still a geek. Professionally and respectfully speaking of course and definitely not a dork that runs around smelling girls bicycle seats.

This discussion is closed to new replies.