Question Locked

New Radeon X1550 AGP card causing PC not to boot

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi,

I have just upgraded my video card from a Radeon 9200SE 128mb AGP card to a XpertVision Radeon X1550 256mb AGP card.

When I installed the new video card the PC gets stuck and posts with unending short beeps, which I am led to believe in Award BIOS this means a PSU issue. I have an Antec 380W PSU so I find this hard to believe it is a PSU issue. I have 2 normal IDE HDD a CD Burner, and a DVD burner so I doubt there is an overload.

When I put the old video card back it boots fine, eliminating any memory issues. The motherboard is a Gigabyte GA-8IPE1000-G which has an AGP 8X slot. The old board is a 8X as well so I dont understand why it is not working. The only differences I can visually see is the new card has 1 long and 1 short slot tab whereas the old one has 3 short tabs, and the new one has a fan, the 9200SE does not.

I removed the old drivers before install but to no avail.

Would claering the CMOS fix this issue ?. I have not tried this yet as I don't want to go there unless I have to.

Hope someone out there has the answer :)

12 replies

by thechas

While 380 watts used to be a decent size power supply, I don't build up anything other than very basic systems with anything less than 500 watts.

I think that the new video card does require enough extra power to max out your 380 watt supply. I also presume that you have at least 1GB of RAM and a reasonable complement of fans. Power draw adds up a lot quicker than you might think.

Chas

by olindahillwines

Thanks Chas

I have 1GB of RAM and P4 3.0 GB Prescott with an Antec Sonata case which, so there are a few fans.

by mjd420nova

Yes, you need way more than 380 watts. I'd look for 550 or 600 watts. Doesn't that card also require a second power connection directly from the power supply??

by olindahillwines

Yes mate it does.

It seems this is the issue now.

This PC will become a 2nd PC in 12 months time so would 600W do the trick for the long haul ?

This site rocks so much help so quickly :)

by olindahillwines

I am looking at FSP Blue Storm 500W ATX V2.0 Power Supply

It has more than the standard four 4 pin units. I need 5 and a fan only one

Would this remedy my issue

by olindahillwines

I have decided on a 600W Atrix on ebay for $90

It has 6 4 pin plugs which suits my needs.

Thanks for all the help :)

by oh smeg

Which is not at all common but I don't think that the PS is the problem in this case.

What I think is happening here is a Chip Set or Firmware issue which is causing the M'Board to hang and not display any video at the very beginning. This most often happens when there is a Mismatch between the BIOS or Firmware Versions on the different Chip Sets Involved. And while you may have had a ATI Card in previously a different brand or firm ware revision may not work with the M'Board.

The Antec PS should be more than sufficient for this load and you need to remember that if it's working properly the rated power is a constant power not a peek power rating.

If you can contact the seller ands ask if there are any known issues between this Video Card & M'Board would be a better option.

Col

by gary56789

The old AGP card uses 1 voltage (either 1.5 or 3.3 volts?depending on card configuration). The new card uses both of these voltages together. Check out this link http://tinyurl.com/jzdkq . You have the wrong card configuration for your MB.

by olindahillwines

Can you get an adapter or tape the excess gold teeth ?

Just bought a new 600w PSU :(

by olindahillwines

Thanks so much for that link - very informative

I am so happy my m/board is a Intel 865 which is a Uni 1.5 V anbd the new card is a 1.5 v connection so with a bit of luck the new PSU should solve my probs.

Thanks so much for the help

by tombarad

I'm experiencing the same issue.

My MB is a Gigabyte GA-K8U-939; upgrading from GeForce MX4000 to Radeon X1550. I have a 500W PS.

Did you have any success?

This discussion is closed to new replies.