Discussion Locked

No desktop

0 helpful
20 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Windows 98SE on a shared machine (with
other family members). I start up the machine,
it goes through what appears to be "the usual"
processes until the end: I hear the "done"
music, but no icons/desktop appear! One
time, I was able to getit to start up in "Safe"
mode, but again no icons/desktop.

20 replies

by wim

your explorer.exe is probably corrupt, try ctrl-esc when you hear the "done" sound and run the program "exlorer.exe"...

by brifd1

This didn't work: I still have the desktop picture and a
movable arrow (not frozen). The only programs that are
open (when I do the first Ctrl Alt Del) are: Csinject, Vsmon,
Sbserv, NProtect, and Explorer.

by thechas

Do you see the 'normal' POST and startup screens while the PC is booting?

How about if you boot from a startup disk, does the display work then?

If the answer is no to both questions, then you have a video card / monitor problem.

If you do get the POST screens, and can boot to a DOS prompt, I recommend that you boot from the startup disk, insert the W98 CD, and run setup to re-install W98.

You normally will not loose any user settings or files.

Chas

by brifd1

I see the following: Compaq (the type of computer),
then "Detecting..." (I have a 2nd HD which I haven't been
able to be usable yet, but I needed a controller? to hook it
up), BIOS..., IDE Master Bus Enabled, Boot Loader
Initialized, Win 98 splash screen, Desktop picture, prompt
to Enter Network Password-I have none, so I click OK,
then the music. I just found a startup disk. That was part of
my problem before. It brings me to a DOS prompt, but with
the message "This program requires Microsoft Windows."
It is the 2nd edition updates...I think that Win 98 was
pre-installed on this computer. Your answer and #3 have
helped, but since the problem still exists...

by charles_j_smith

There are many possible reasons for this happening - virus, someone deleted important files, corrupt system files. When you can not even get to the desktop in Safe Mode, I typically will reinstall the OS (simply because looking for a resolution most of the time -- at this point --takes too much time).

If you choose to try and save Win98, try this link:
http://support.microsoft.com/default.aspx?scid=KB;en-us;q188867

If you want to go ahead and reinstall the OS (without reformatting the HD so no data files are lost, I highly suggest you reinstall to another directory - not to the same Windows directory). Something like c:\win98 will do. You will have to reinstall all the applications and such, but the good thing about this is that nodata will be lost (like favorites, email, etc.). Ensure you have adequate virus protection and ensure that it is up to date.

If you need more information, let me know.
Chuck

by brifd1

I just found a startup disk. That was part of my
problem before. It brings me to a DOS prompt, but with the
message "This program requires Microsoft Windows." It is
the 2nd edition updates...I think that Win 98 was
pre-installed on this computer. By the way, the link above
did not work. Your answer and #2 have been helpful, but
since the problem still exists...

by thechas

Here is the correct link from answer 3.

http://support.microsoft.com/default.aspx?scid=KB;en-us;188867

Remove any spaces from the pasted link.
Microsoft recently changed ALL of their Knowledge Base Article addresses.

If you have a startup disk, you should be able to boot from it, and run setup.

However, if your W98SE CD is the W98 to W98SE version, and not the full W98SE upgrade, you MAY need to have Windows running to use it.

You may need to find the original W98 CD, or borrow a W98SE CD.

What it looks like from your boot description is that either files, or the registry are corrupt.

Here is a link to a Tech Republic article on rebuilding the registry from DOS.

https://www.techrepublic.com/article.jhtml?id=r00320000807det01.htm&src=search

This could also be a problem with your anti-virus software, memory, or video driver.
Since the problem exists even in safe mode, I suspect missing files, anti-virus, or bad memory.

Chas

by brifd1

The Tech Republic address appears to have been
changed, too-to
https://www.techrepublic.com/article.jhtml?id=r0032000080
7det01.htm&src=search&_requestid=203637
It's been a long time since I've used DOS commands, and
I can't tell whether they're using a small L or the number
one (first step). I used Ls, and I got "Parameter value not
allowed -ls" and "Parameter value not allowed
-c:\windows\user.dat" as error messages.
Yes, I think I have the W98 to W98SE version. Also, the
drive is partitioned (Partition Magic). Is one possibility
"simply" to upgrade the OS to 2000 Professional or XP (it's
a 450 Mhz with plenty of RAM and hopefully enough
space). Also, I had copied the system to the partitioned "D"
drive, but that does not show; D is instead the first CD
drive.

by thechas

Do you see the extended DOS partition when you run fdisk?

If not, then the drive may have a BIOS / drive overlay program on it.

You need to boot up and watch for the prompt for the drive overlay utility.
Enter the program, and follow the instructions for a Floppy boot.

If there is not a drive overlay program installed, you can TRY using fdisk /mbr from the DOS prompt.
However, if Partition Magic used any special utilities to set up the D: drive, you MAY LOOSE it. Use this only as a last resort and with CAUTION.

Do you have some way to back up your data files?
If so, then I would give W2K or XP a try.
Check the HCL to make sure that all of your hardware is XP compatible before proceeding though.
Many Printers have reduced functions under XP.

Boot from your startup disk, and run fdisk to delete all partitions and logical drives.

Then, boot from the OS CD, and run setup.
If you cannot boot from a CD, you can create a bootdisk set for W2K from the CD.
For XP, youneed to download the file to create the boot disk set. There are now 4 versions of the file, so make sure that you get the correct version.

One side note on XP, if you expect to upgrade or replace the PC within 6 months, I would do that before loading XP or W2K for that matter. Neither likes moving to new hardware.

I'll be going off-line soon.
Be back tomorrow if you have any more questions.

Chas

by brifd1

I tried running FDISK and FDISK /mbr from a floppy
that I had labeled "startup disk," but neither worked. I am
not familiar with the acronym HCL, but at this point just
want to have the computer working again. I am tempted to
get a new internal HD and have an OS installed on it,
making it the primary HD and then dealing with the
original primary HD.

by rcom

When you use Ctrl-Alt-Delete have you tried stopping the programs? Do you know what Csinject, and Sbserv are? Also if there's a virus there may be a possibility that a command is being started from the Win.ini file. You can check and edit the file in DOS and put a semi-colon character ; in front of anything that's in the run or load lines. This will disable the command and can be undone later. To do so from the DOS prompt, type in "edit C:\windows\win.ini" The run and load lines are in the first section. If there's any commands there Put the character in front of each line. To save press alt then scroll down to exit and choose yes when prompted.

Since you assume that this was a pre-installed version of win 98 the setup cab files may belocated in the Windows\Options\Cabs folder. If so you can reinstall the OS from there. Boot to DOS hit F8 before clouds screen appears and choose command prompt only or F5 as soon as the starting windows 98 prompt appears.

Type in "CD windows\options\cabs" from there if the files are available you can type in "setup" and go from there. I don't remember but you'll probably need the Product Key. If you don't have it and can get the PC to boot and function in safe mode you can get the product key by running regedit. Select "Edit" from the top and scroll down to "Find".
Type in "ProductKey" (no spaces)
write it down so you have it if needed.

by rcom

You mentioned about the original drive being partitioned with the second not showing up? That issue needs to be resolved. As Chas mentioned the drive may have an overlay program like easy bios installed. To check boot the hard drive to a DOS prompt (press F8 before the win98 cloud screen and select command prompt only) does the second partition show up then? If you run fdisk and select option 4 to view details can you see the extended partiton?

Another issue you've mentioned that is puzzling is about the second hard drive not being in use without a controller. I don't get why that would be needed. Is it hooked up at all? You can have 4 devices attached to the IDE ports. Do you have 3 other devices installed i.e. CDROMs, IDE tape drivesetc besides the hard drive. So connect the second hard drive to IDE 2 or as a slave to the first drive don't forget the jumpers. If the CDROM is attached to the second IDE channel attach it to the second drive and jumper it as a slave or as Compaq likes to use CS (cable select).

by brifd1

I have no idea what those programs are. There's nothing
in from of the run= or load= lines. There is no
sub-directory in the Windows sub-directory called "cabs."
Too bad one can't do a global search. There is a "cabs"
sub-directory on theSE additions CD, but setup doesn't
do anything. The 2nd drive issue was posted here awhile
back, but no solution presented ever worked. Now, of
course, one can get much larger HDs for the money. The
2nd HD has its own controller due to therebeing a CD
burner, DVD player, and Zip drive. It showed up in
Explorer, but as a fraction of its actual size.

by mnman

Are you using a Compaq Deskpro? The older ones with the Matrox graphics card, M100/M200 have been known to go bad. You can either go to the Compaq website, or to the Matrox website and get the update for the CMOS for the card, or the actual drivers,since you can get a desktop in safe mode. If this still doesn't work, we can try other things as I've been through this a few times. Email if you need!
Good Luck!

by brifd1

No, it's a Presario 5116. I can't get to the desktop in
safe mode, either.

by thechas

Sorry about the acronym.

HCL stands for Hardware Compatability List.

Microsoft maintains a list of supported hardware for their operating systems.

It is a good idea to check the list before upgrading to a new version of Windows.

I also check all of the hardware manufactures web sites for drivers or cautions for a new OS.

Some printers on the HCL print in XP, but have many functions disabled.

I tend to agree with your tact of installing a new drive as the master and installing Windows on it.

At this point, it may be your best option to recover any files on the old drive.

You may need to use a file recovery utility.
www.ontrack.com is one source to try.

Chas

by brifd1

I was originally thinking about adding a larger HD,
say 60 GB, since I have 1 more slot (although, ultimately,
I'd probably want a DVD burner should there ever be a
viable one). How about this as a low cost alternative, what
about the existing second drive? What would happen if I
switched the jumpers so that it became the primary drive
(it's only 20 GB, but that's twice what the original drive is)?
What would happen at startup? Is there some basic
startup program that results in a DOS prompt there? If so,
then I presume that I could install an OS from CD onto that
drive there (that is the drive that only shows as 4 GB at H:
when I was able to use Explorer from the 1st HD. I may
have found a Win 98 SE CD.

by brifd1

I ended up getting a new, larger HD and
getting an OEM version of Windows XP
Professional. Now, it works fine, with the
exception of dealing with incompatibilities,
most notably the printer. I'd like to award
points anyway, we'll see if TechRepublic
allows it "after the fact."

This discussion is closed to new replies.