Discussion Locked

print sharing problem Windows ME and 98

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

The configuration:
1. Dell Dimension desktop running Windows ME connected to Xerox 470CX multifunction printer. No firewall (while testing).
2. Toshiba Tecra laptop running Windows 98
- both have the latest printer drivers from Xerox
- printer and file sharing enabled on the desktop
- the laptop can see and read files on the desktop
- the shared printer shows up on the laptop
- the printer works when connected directly to the laptop's parallel port

Problem:
I can't print via the network. Symptoms: no job shows up on the job q (on either system), no errors are reported, nothing is printed.
I noticed on the desktop that the description of the File and Printer Sharing network component specifically says it will enable sharing withsystems running Windows NT or Windows for Workgroups. So am I doomed to failure here?

12 replies

by sgarr

No login. I should have mentioned - this is a home setup. Just the two computers on the network. No login prompt is presented when I boot. Should it be?

by cg it

How are you connecting the computers to each other? hooking to a hub or switch? or direct PC to PC?

also, make sure TCP/IP is enabled as a network protocol. Go to Start, Settings, Network and dial up connections and open network/dialup settings. You should have a connection named local area connection. If not you'll have to create one. If you do, double click to open, then click on properties at the lower left. you should have client for microsoft networks, print & file sharing for microsoft networks and as a minimum NETBEUI protocol [TCP/IP is a better protocol to use but requires configuration. NETBEUI does not.] If not, install these. after which Windows will prompt you to reboot.

by cg it

To answer your question, No, for a home network with just two computers, no log in is necessary. but you do have to enable file and print sharing in your local connections network properties [see above].

by fenaikh

Hi

pls do the flowing if you did not do it before.

1. Start->help->Home networking
2. Start-> Programs-> Accessories-> Communications-> Home Networking Wizard. Then select I want to edit my home networking setting in this computer. Continuethe options till you reach "yes, create a home networking setup disk".
After you create the floppy then use it with the notebook (win 98) to setup home networking.

3. You said it worked in the notebook (Win98) with paralle port, but have you tried to access it as a network from desktop winME?

if it worked in No.3 then there are maybe settings is missing such as:
1. some printers need a specific port type such as the ECP port set in the BIOS specially when aaccessed from netork.

2. Read this from help.
Start -> help -> Sharing use of files or printers from remote computers

"To allow others to manage your files and printers from remote computers

Open Passwords properties in Control Panel.
Click the Remote Administration tab.
Make sure that the Enable remote administration of this server check box is selected.
Notes

If there is no Remote Administration tab, the computer is not set up to give others access to your files. For information on allowing others to manage your files, click Related Topics below.
If there is no Administrators list on the Remote Administration tab, your computer is not set up to control access by using a list of names. For information on controlling access with a list, click Related Topics below.
You must have at least one valid entry in the Administrators list for remote administration to be effective.
Another way to open Control Panel is to click Start, point to Settings, and then click Control Panel. If you don't see the item you want, click view all Control Panel options."

if this is did not help pls supplu more info such as

1. Are you using home networking or microsft networ or

by fenaikh

if this is did not help pls supplu more info such as

1. Are you using home networking or microsft networ or direct cable connection.
2. Have you installed the driver in the note book as a local or as a netork.

Good luck

Mohamed

by fenaikh

Hi

http://www.support.xerox.com/SRVS/CGI-BIN/WEBCGI.EXE/,/? St=197,E=0000000000040790753,K=9836,Sxi=11,Case=obj(13695)

Answer no. 4 gives you the link up and it says as:

" Online Support Assistant
WorkCentre 470cx Color All-in-One
Solution: The Xerox Printer is Not Supported on a Network
The Xerox printer is not supported in any type of network setup or environment. Xerox only supports a direct local connection, meaning that the printer should be directly connected to theparallel port on your computer with an IEEE-1284 Compliant Parallel Cable, with no peripheral devices in between. "

that means the driver came with the printer may not support network of any type , but you could try other driver from same vendor or other windows supplied driver for otther compatabile driver it may work but vendor will not support it.

Good luck

Mohamed

This discussion is closed to new replies.