Question Locked

Symptoms of PSU under power?

0 helpful
12 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi, i'm building a new pc using my present working lcd screen. This new pc's chassis has a LCD front panel (coolermaster cm-282).

I've assembled the pc. When i start the pc, the cpu fan and chassis fan is running, and the front panel LCD (of the chassis) is lid. But there's no vga signal, black screen.

I've troubleshoot and found out that:

When i connect the LCD front panel (of the chassis) to the psu power supply, my monitor gets no signal at all (black screen). The monitor is still in standby mode (the LED on the monitor is orange color)

But when i disconnect power to the LCD front panel (of the chassis). The monitor is no longer in standby mode (the LED on the monitor is green). And i get a message (from the monitor) saying "signal detecting something", which is shown on and off the black screen (note: the monitor itself is ON all the time. The LED on the monitor is green)

Is this a sign of my psu under power?

Please reply, thanks.

12 replies

by dumphrey

on what video card you are using and what power supply. But it sounds more like your computer does not know which "monitor" to use. It could be detecting the front panel LCD as the primary monitor. Can you see adesktop on the front panel LCD? And if so, can you browse to your video card settings and enable a second desktop on the other monitor?

by jack0jack

Hi,

The chassis (CM-MEDIA 282) is a media center / home theater chassis. The front panel LCD screen i meant functions as a VFD screen, but uses LCD tech (i should have been clear), check the coolermaster website and you'll know what i mean.

I couldn't find its watt consumption. There's one chassis fan.

The motherboard is M3N-H, it has a built-in nVidia GeForce 8300 video card. I don't how many watts it cost to run and i cant find this info on asus's website.

The cpu is AMD Athlon x2 6000+, consumes 125watt. And there's of course, the cpu fan that comes with the cpu.

The memory is 2gb ddr2 667.

No harddisk, dvd drive attached yet.

Power supply unit is coolermaster "eXtreme power plus" ATX 12v v2.3 460watt.

The manual of the motherboard mentioned that:
"for a fully configured system, we recommend the use of a psu of ATX 12v 2.0 (or above), and provides a minimum power of 600 watts"

That's 600 watts (minimum) for a fully configured system.

But it doesn't mention how much watt for partially configured system.

by Former member

Does LCD work elsewhere? Does another monitor work on the computer? Sounds like your'e underpowered. Does it sound like it booting? ANy beeps?

by thechas

Typically, if the power supply is so under-rated that it cannot supply enough power for the system to at least POST, the PC should either shut down or sound an alarm.

You have a POST problem.

Start by checking all of the configuration jumpers and the power connections. You did plug in the extra 12 volt 4 pin power connector.

Next, remove or disconnect as much hardware as possible. Have no drives connected and just the video card plugged in.

Another thing, check that the switch on the power supply is set to the correct line voltage.

Chas

by jack0jack

Thanks for the reply.

I've connected all the power cables firmly, including the 12 volt 4 pin. The voltage for the psu is set correctly. The LED on the motherboard is lid green, from the manual it means its powered on.

The manual did mention that:
"... ATX 12v v2.0 500watt has been tested to support the following configuration:
cpu: AMD FX-62
mem: 1024 mb ddr2-800 x 4
graphics: pciex16 nvidia 7900 gtx
sata harddisk x 2
dvd-rw drive"

There are only two jumpers on this board: the clear RealTimeClock, and the Chassis Intrusion. Both left untouched.

Harddisks or optical drives are not connected .

The RAM is tested on another pc and was detected at POST.

When i boot this new pc, there's no vga, and no beeps whatsoever. So i can't tell if it even went through the first stage of POST 'cause i can't see on display, and i didn't hear any short beep (usually the default bios sets pc speaker to ON, so when i power up the computer, the should be 1 short beep prior to the first stage of POST)

When i disconnect the RAM, i gives "one long beep, and two short beeps", which means display card problem. Reasonable, 'cause the built-in video card uses shared memory.

by thechas

That you get a beep when you remove the RAM is encouraging.

The symptoms imply that something is stopping the POST process.

The "best" next step would be to use a POST card to see where the POST is stopping.

You might want to pull the motherboard out of the case to make sure that no feet are shorting things out.

Chas

by jack0jack

The monitor works. I'm using it right now.

There's no beep whatsoever when i boot.

But if i remove the ram, it will sound 1 long beep and 2 short beeps - video card problem. Which is reasonable 'cause the built-in video card uses shared memory.

The ram works by the way, i tested the ram on another pc and its detected at POST.

by jack0jack

Thanks again for the reply.

Okay i couldn't get a POST pci card yet, but i've managed to try other stuff.

I borrowed a 620watt working psu. Same result: led on, fan on, ram attached, cpu attached, no POST beep. This rules out psu problem. But i'll keep using the 620watt psu for the rest of the test just in case.

I removed the motherboard and place it on a anti-static plastic bag on a flat surface. Tried booting again, same result: no POST beep. Removed ram, 1 long beep 2 short beeps. (One more thing: did i mention the heatsink was cold the entire time?)

I tried something else: i removed the heatsink and the cpu. I was expecting repeating high/low beeps as documented by Award Bios beep codes. But there was no beep!

Then i remembered the retail shop who sold me this motherboard told me the supplier were out of stock and they have to get it from a factory warehouse or something.

Could a bad BIOS 'cause this behaviour? Do suppliers have to flash the BIOS before delivering it to the retailer (is this how things work)? I do notice a marker written "M" on the BIOS chip on the motherboard, don't know if it means anything.

by oh smeg

But on some M'Boards there is a jumper to clear the BIOS and this is 3 Pins with the Jumper normally on Pins 1 & 2 to supply power from the CMOS Battery to the RTC. When the Jumper is on Pins 2 & 3 there is no power tot he CMOS and this causes a lot of problems with not booting.

Look in the M'Board manual and check the setting of the CMOS Clear Jumper. Some M'Board makers ship their M'Boards this way to prevent th CMOS Battery going flat.

Col

by jack0jack

Thanks for the reply.

I manage to get my motherboard tested with my friend's AMD Athlon64 x2 4000 processor and it would POST no problem (POST beep, bios setup, detects SATA hdd, optical drives, no errors).

In the mean time i've also tested my AMD64 x2 6000+ (the one i own) on my friend's AM2 motherboard. It too was detected and was able to POST with no errors. But my processor's name displayed during POST was "AMD processor model unknown".

Both motherboards are installed with 667 DDR2 ram. Is it something to do with my motherboard's CMOS bios, now that i know that my processor and memory module are not faulty?

by oh smeg

SO to do this assemble the system power on and enter BIOS. Set the CPU to the Correct Settings of FSB and Multiplier and so on and then see if things work OK. Just remember to save the changes on Exiting BIOS and then reenter BIOS to check the settings.

If you saved the changed on Exit and the CPU is still not recognized then you can start to think about Flashing the BIOS to a newer one if there is one available.

Col

This discussion is closed to new replies.