Question Locked

[UPDATED] SLI nForce 650i SLI(C55) - How does BIOS restore work?

0 helpful
21 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

36 hours ago, I noticed file accesses slowing down, directory accesses taking far too long.

Event Viewer showed a string of errors with Event ID 11. There were 2 instances of this:

1. The driver detected a controller error on \Device\Harddisk1\D.
2. The driver detected a controller error on \Device\CDRom0.

So, it's a 6 day old 500GB HDD which just happens to have ALL the content from my Acer laptop (as a safe means of backup). I had then cleaned out the laptop HDD for efficiency.

Phoned the Tech Support for MESH:
He suggests that I [b]reinstall[/b] the OS (XP Pro) which is sitting on a separate, smaller HDD in case that might fix the problem which he thinks is a driver issue!

Any thoughts ??

Should I lose all my newly updated OS in case it is just a driver issue ??

[u]Another thing:[/u]
The next boot was interminably slow. I assumed it was because the page file that had been sitting on the missing disk was now also missing, so the OS was booting with no pagefile.

I transferred the pagefile back to the C: drive, but the boot is still 9 to 10 minutes.

Do you reckon the other drive is going ?

System Spec:

Intel? Core? 2 Duo E6850 Dual Core Processor(3.0GHz,4MB Cache,1333MHz)
Genuine Windows? XP Professional Edition [upg] (from Vista)
New MESH Midi-TowerATX Case + 550W PSU
PCI-Express Mainboard - SLI nForce 650i SLI(C55) - Intel Core 2 Duo/Quad-Core - ATX
2GB DDR2 667MHz Memory - (2x 1GB)
750GB (1x 500GB + 1x 250GB) Serial ATA Hard Drive with 16MB Buffer
LightScribe Super Format 20x Dual Layer DVD Writer +R/-R/RW/RAM
512MB nVIDIA GeForce 8800GT - Dual DVI, HDTV, TV Out
22" Widescreen LCD TFT Digital Display with internal speakers (DVI, 5ms)
5.1 High Definition onboard sound card - 6 Channel Cinema sound
Logitech S220 - 2.1 Speakers with Subwoofer
Logitech Cordless Keyboard & Cordless Optical Mouse
6x USB 2.0 Ports (10x possible on motherboard)
2x IEEE1394 Firewire (onboard)
1x Gigabit LAN (onboard)
Multi-format Memory Card Reader (matx)
Platinum - 3 Years On site Service - UK Mainland Only (Repairline Ltd Warranty)

21 replies

by rob miners

Check that the BIOS settings haven't defaulted. Make sure that all drives are detected.
Update the Chipset Drivers.

by older mycroft

There are 2 drivers out of date:

Nvidia Network Bus Enumerator
Nvidia nForce Networking Controller

That's it.

by cg it

control panel/admin tools/disk management. Does disk manager see the drive?

and what does device manager show for the SATA controller?

AND

do you use a RAID array? or
JBOD? [just a bunch of disks]does the RAID controller see the drive?

could be the damn SATA cables, could be the damn SATA power plug, could be the HDD is going out [not 100% error proof]

could be the SATA connector on the board,

by older mycroft

The BIOS doesn't recognise the 500GB drive.

There is a BIOS Restore capability but I honestly don't know what to do with it. Do I invoke the reload ?

There are two BIOS profiles, each with 2 save points.

What would happen if I reloaded from an empty save point?

by rob miners

checked the manual just yet. But rereading the errors. Check that the smaller drive is in Sata Slot 0 the 500 is in Sata Slot 1 and CD/DVD is in Sata Slot 3 or 4

by older mycroft

C: is in Slot 0
The event id reports D: was in Slot 1

Can't be sure about the opticla drive but when I had a rummage inside the case there are 4 SATA sockets in a row.

From left to right > C: is 0, D: is 1, 2 is empty, DVD is 3.

I'll tell you - when I saw this BIOS it reminded me of how I felt when I first saw a colour television !!

SMART was turned off - typical! :(

by older mycroft

Disk Manager doesn't show D: at all. Funny thing is it hasn't reassigned the letter, the letter D has just evaporated.

All I've got is C:[Recovery] \ C:[System]
E: DVD

When I checked the BIOS it turns out the SMART was turned off - typical!

JBOD - keeping it simple.

The RAID is not invoked within the BIOS.

:::::::::

I recall seeing an Event ID (can't remember the code) which meant Bad Cabling. Before I could do anything about it ~coffee stop~ the BSOD arrived. On restart there was this string (25+) of Event IDs
Error code 11 "The driver detected a controller error on \Device\Harddisk1\D."

Checked all the SATA cables, re-seated them, but apart from them ALL being a bit wibbly-wobbly it all seems normal.

I was expecting the SATA to have fallen out.

by cg it

turning on or off SMART shouldn't effect the SATA controller.

I think it's the drive or SATA drivers. If you updated drivers roll em back.

by older mycroft

I sought the aid of the famous Microsoft Hinder & Cripple Wizard.

Using its unerringly accurate advice it steered me to the point of reinstalling the SATA drivers - which instantly took me directly to the BSOD. Restart arrived at Safe Mode options.

The SATA controller in device manager doesn't see D:.

The boot sequence is still taking 10 - 12 minutes to complete. I reckon it's because I had the pagefile on the now defunct drive. I've put the pagefile back to C: but the boot sequence won't have changed because I can't tell the system that the pagefile has been removed from D:.

All in all it's a sh!tload of trouble.

by rob miners

they being picked up in the BIOS.

I forgot to add after you reconnected them.

by older mycroft

In the BIOS along with the DVD.

If it wasn't that I'm looking through the open side panel right now, I'd think I was imagining the D: drive.

I'm eagerly awaiting the arrival of the Support Engineer to see what he makes of it. But until Mon/Tue I'll have to have a dig around.

by rob miners

out of curiosity what are the Makes of the Drives. It looks like the controller has gone on the 500. What happens if you disconnect the smaller drive and CD/DVD and put the 500 on Sata Slot 0. If it dosn't pick it up it must be shot.

by cg it

Bottom line is if you reinstalled the SATA drivers and immediately get a BSOD, then ha ha you know the answer.

how to fix?

Not sure...If there isn't anything on the 250 drive you can't afford to lose, wipe it, start over. If there's stuff on the 500 drive you can't afford to lose, then I would disconnect it until you get the O/S stable on the 250 drive.

I also wouldn't use the new NVidia drivers but the ones that came with the motherboard [or on the OEM disk] I've had problems like this with NIC drivers, Video drivers, from nVidia that Windows Update says newer ones are available.

Have you tried resetting the BIOS to defaults on all pages?

you could try the manual detect for HDDs and DVD/CDs it's possible the BIOS is running on the Mumbo....

by older mycroft

Because of the crash after reinstalling the SATA drivers ...

What is your point?

Are you saying you reckon the OS has become unstable?

I've been thinkin' about this for far too long today. Can you clarify?

by cg it

the O/S is on your 250GB hard drive and the new drive is the 500GB and that's got your backups on. It's also the drive causing problems.

So if there isn't anything on your 250GB drive that you must have, then I would wipe it clean and reinstall the O/S on it. Don't have the new 500GB connected while you reinstall.

Once you've got XP reinstalled, and your using the right controller drivers, try updating them to the new oners [without the 500GB connected] See if that causes the same problem.

by older mycroft

So.

Post re-install:

System appears stable now, check in later . . .

by older mycroft

D: is still not 'visible'.

Having tried :::: Now gonna re-set the BIOS

by older mycroft

New motherboard

New 500GB hard drive

System now running at full capacity.

Job done.

This discussion is closed to new replies.