Question

Locked

Rebooting Issue Please Help

By Koopa24 ·
I'ma start off with my specs

MSI X58M intel x58 chipset

LG GH22NS50 Black SATA 22X DVD RW Burnee

SEAGATE 500GB Desktop Hard Drive

Intel CORE i7-920 CPU Processor 2.66 GHz

Rosewill R223-P-BK 120mm Fan ATX Mid Tower Computer Case

G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600

COOLER MASTER eXtreme Power Plus RS-500


Ok this has been taking me forever to try and figure out. i have a MSI X58M Mobo and when i start up my PC it turns on for 30 secs and reboots so i tried taking off the fan and when i did that it booted up every 10 secs. So i knew that there was a overheating problem right than and there because i tried everything that they said to do in that sticky thread. I tried everything, i don't know what could be the problem. I unhooked everything and put it back together and still nuthing. Can someone please give me some help. Thanks.

This conversation is currently closed to new comments.

7 total posts (Page 1 of 1)  
| Thread display: Collapse - | Expand +

All Answers

Collapse -

Memory may be wrong for mobo chipset?

by seanferd In reply to Rebooting Issue Please H ...

http://www.gskill.com/products.php?index=227&c1=&c2=
(Intel P55)
Qualified Motherboards List
MSI P55-GD65
MSI P55-GD80

http://www.anandtech.com/mb/showdoc.aspx?i=3568&p=2
(Intel x5

Otherwise:
Do you have overclocking settings in BIOS?
Have you checked memory timing, etc., in BIOS?
CPU fan properly seated with thermal paste?
Is airflow unobstructed?
Is RAM in the correct slots for 2 sticks?

What happens if you disconnect drives and any (unnecessary for testing) expansion hardware?

Have you tried with 1 stick of RAM? No RAM?

Collapse -

Checked Them

by Koopa24 In reply to Memory may be wrong for m ...

I can't even get to the BIOS because it keeps on rebooting.

CPU is seated on the thermal paste

airflow is not unobstructed

I have tried with both sticks, 1 stick, and also no sticks.

When i disconnect any drive it does the same thing

Collapse -

Are you saying that it was working and now it's not

by Jacky Howe In reply to Rebooting Issue Please H ...

You can use the Hard Drive Makers Testing Utility to Test the Drive which can be downloaded from below.
<a href="http://www.hgst.com/hdd/support/download.htm" target="_blank"><u>Hitachi / IBM</u></a>
<a href="http://support.wdc.com/download/index.asp#dlgtools" target="_blank"><u>Western Digital</u></a>
<a href="http://www.fel.fujitsu.com/home/drivers.asp?L=en&CID=1" target="_blank"><u>Fujitsu</u></a>
<a href="http://www.seagate.com/support/seatools" target="_blank"><u>Seagate</u></a>
<a href="http://www.samsung.com/Products/Hard...ties/hutil.htm" target="_blank"><u>Samsung</u></a>

Also try a repair install.

Collapse -

CPU is seated on the thermal paste ?

by Jacky Howe In reply to Are you saying that it wa ...

I hope that the grease is between the CPU and the Heatsink.

Edit: have you connected the power source to the CPU. It's a four pin connector and normally has two black and two yellow wires.

Collapse -

Thermal paste?

by Koopa24 In reply to CPU is seated on the ther ...

I have to buy thermal paste? I thought that it already did it on its own

I have connected the power source to the CPU

Collapse -

Don't try to run it

by Jacky Howe In reply to Thermal paste?

until you have cleaned off the old residue with a cotton cloth from the top of the CPU and the bottom face of the Heatsink. Arctic Silver is a good brand and it should be applied sparingly each and every time that the Heatsink is removed. Each tube that I buy is good for 5 applications.

I also notice that there are LEDs for the CPU and Memory. Check your Motherboard manual.

Back to Desktop Forum
7 total posts (Page 1 of 1)  

Related Discussions

Related Forums