Question Locked

Cannot Renew IP Address

0 helpful
10 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

Hi guys,
Thanks for taking the time to read this.

Im having problems with my ip address in my wireless card. I have read a lot of information on the internet about how and what i can possibly do, but i cant find a solution.

My address is a 169 ip, which i read will not allow my computer to access the router internet information in my network. Every time i restart my computer i do not have a problem with my wireless network, however when the wireless drops out im left with a signal, but a 169 ip.

My DHCP is all enabled, everything 'should' be working except i cant get the ip to renew after ive lost a signal.

I have tried:
ipconfig
ive uninstalled and reinstalled the card
ive downloaded "winsock" and that wouldnt help
looking through all the properties/options

If anyone has any solutions to my problem that would be greatly appreciated!

Cheers,
Alex

10 replies

by kjell_andorsen

If you know the default IP address for your wireless router (usually something like 192.168.1.1 or 192.168.0.1) you could try setting a static IP address on the card that's on the same subnet and make sure you use the router's IP address as the default gateway.

If this works I would say chances are there's something wrong with the DHCP settings. Are you getting DHCP from your router or a different DHCP server?

by vinitogupta

hi,

You cannot renew ip on your box or on the router......if its box just try this ipconfig /release and then try renew

let me know where you having problem

thanks

by fosiul

Hi,
u said dhcp is enable , is this at router or in operating system (server) ?

Can you put a static ip address , pick any from your dhcp list, and exclude that one from dhcp list as well.

and also, when your connection dropped then can you check if its trying to connect to other people's network or not By "view available wireless network" and check your connection status.

by benjamin.bone

Hi,

Start at the bottom, if you are using a PCMCIA wireless card, remove it. If not, just disable your onboard card. Go into your command prompt and type ipconfig /release it should 0 out your ip settings. Enable your PCMCIA card, if your provider is using DHCP then your computer still owns the lease information for your ip.

Should work,

Good Luck
Ben

by sgt_shultz

i had this problem once. it turned out to be the customers satellite tv interfering. i would see if i could get the wireless dropout problem fixed. only other thing i can think of is some kind of firewall problem but that doesn't fit with your 'reboot fixes it' symptoms...

by tcp 765

You should check the power rattings of the signal that your PC is receving.

This is the first thing to chech. If there is any interference the DHCP request information would not be delivered properly.

Also check that you are using the NIC drivers of the manufactor an not the windows Drivers, (Those Stinks).

by 45geek

You didn't say what kind of card you were using. But I have run into this problem more than a few times before. You've had some good suggestions and you should always try the easiest first or at least the ones that you understand the best first. IP release is the best and should be your first start. Next I would check for interference, like one of the suggestions (try a different channel, move the two closer together) Next and what I've had the most problems with is DHCP on wireless with the request for an update not sync'ing properly and then changing the ip and losing contact with each other...I usually solve it with a static IP. But 9 out of 10 a drop in wireless is interference causing the signal to lose sync and then dropping the connection. Drive you nuts.

by ic-it

to post your own question. This thread is over 2 years old. ;-)

Here are a couple of simple things to try and isolate the issue.
Open your wireless network connection properties.
On the General Tab, where it says connect using, click on Configure.
Select the Power Management Tab.
Uncheck the box next to where it says allow the computer to turn off this device to save power.

Another thing to do is be aware of your location and surroundings. Microwaves, wireless phones, and other devices can interfere with the signal.

This discussion is closed to new replies.