Question Locked

Changing Mass Storage Drivers on an established server.

0 helpful
9 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

I am using a Intel S3200SH server board with Microsoft Server SBS 2008 and the onboard RAID 1 controller setup using the Intel Storage Matrix configuration. I have had several lock ups during heavy drive access usually during backup. After talking to Intel TS they said that it was due to the fact that the RAID 1 Volume was using the Intel Storage Matrix, Which they do not recommend. Their recommendation was to reconfigure and use the LSI RAID Configuration.

Problem #1: I backed up using Microsoft?s full system backup. After reconfiguring the RAID 1 to use LSI configuration. I attempted to restore to the LSI RAID 1 array and received an error saying essentially that you cannot restore to a smaller disk. Tried making the System OS partition larger by using DISKPART but that did not work. Attempted to restore the Volumes manually by using the commands in WBADMIN, still could not get the partitions restored. Microsoft fails to restore if the disk or partitions are not the same size or larger, which is absolutely ridiculous! Does anyone know how to get around this?

Problem #2: Assuming I can recreate the drive partitions using the new RAID 1 LSI configuration and restore using Microsoft?s total system restore. When I reboot the system it will still have the Intel Storage Matrix Drivers installed and I will have to Install the LSI drivers before I can continue. How can I install the drivers before the system comes up? Are there any ways to install the LSI drivers up initial boot with the new configuration?

Thanks in advance
Mark

9 replies

by peconet tietokoneet

You might need to update your BIOS to handle the LSI raid. This should get you out of trouble. The only thing now would be trying the restore of which i do not think would work unless you are restoring from a external device. Why i say this is because when you do a different config of RAID on your system you will be faced with a format of the drives BEFORE you can continue. SO make sure you have backed up your work onto a external device first. I hope you have done this, otherwise you will have one hell of a job trying to get everything up and running.

by markcathi

Had no problem setting the LSI mode in the Bios and then establishing, initializing and getting the LSI RAID array up and going. The problem is when I asked Microsoft system restore to reestablish the Partitions and Data. When trying to do a full system restore the error comes up and says you cannot restore to a smaller disk. Error message is 0x80042407, which when researched basically says you must put in the same or larger disks. Nonsense! they are the same drives just different RAID structure. There is no hardware problem it is Server 2008 that is the problem.

Mark

by darryl~

Starting from the original RAID configuration...

I have taken a GHOST image of the disk...

I resized the partitions in the RAID...

I restored the Ghost image to the smaller partition (Ghost will allow you to restore to a smaller disk than the original providing you have enough space for the data)...

You should now be able follow through with your MS full system backup & restore to the new LSI RAID configuration.

Hope that helps.

by markcathi

What version of Ghost works with Server 2008? and while I like the idea it is Microsoft's 2008 full system restore that seems to have issues with disks/partitions that are smaller than original. I cannot believe that Microsoft's backup and restoration product is just so stinking finicky.

Listen to the quotation from a Microsoft product team member for the Server.

"I understand that it will be reasonable to edit the backup so that the bare metal restore process can accept the smaller disk size, our product team are aware of this desired functionality and will definitely keep this in mind as future product development continues.
Thanks for your understandings."

The worst part of it is that the only thing that has changed is the RAID array structure! Why would a manufacture screw your ability to restore because your HDD size might be a couple of MB smaller. Just plain Stupid!!!

Mark

by darryl~

I do have it documented somewhere...I could find it if I have to...but this is how I think I did it...

It was with 2003 but 2008 shouldn't be a problem (I don't think)

#1 I pulled one drive from the array to make sure I had a backup & set it aside.

#2 I used a boot CD that I had Ghost on to boot the server.

#3 created an image of the partition (not the entire disk) and set it aside

#4 Recreated the array to the desired size

#5 Booted the server with the boot cd & restored the imaged partition to the new partition in the newly created array.

I can dig through my old notes about when I did it if it's giving you trouble...it was 2 or 3 years ago since I did it.

by markcathi

I might be able to recreate the partitions and restore the data on them, but Does anybody want to try to address the second part of the issue?

Problem #2: Assuming I can recreate the drive partitions using the new RAID 1 LSI configuration and restore using Microsoft?s total system restore. When I reboot the system it will still have the Intel Storage Matrix Drivers installed and I will have to Install the LSI drivers before I can continue. How can I install the drivers before the system comes up? Are there any ways to install the LSI drivers up initial boot with the new configuration?

by darryl~

Rebuild the old array & make it "smaller" before restoring the Ghost image ;)

Then restore the partition to the "smaller" array & do your MS backup...build the new array the way you want it...."then" do the restore...I think you know what I mean....pm me if not....I'll find my notes.

by fabster2000

Hi, I`m in the same boat as you. have you fixed your issue by moving from matrix to LSI ? if so, how did you do this and is the system stable now ? thank you

This discussion is closed to new replies.