Question Locked

Is there a way to have two routers coming from one modem?

0 helpful
11 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I work on a boat and we already have one wireless router connected to the modem using a cable and we would like to get another router on the other side of the boat and I was curious if we could use a splitter to split the cable and run the cable from the modem to the wireless router in the galley and still using the split cable run it to another wireless router on the other side of the boat?

11 replies

by ramvicious

I work on a steel boat and it's almost impossible to get any reception in different parts of the boat because of that. For example, we get almost no cell phone reception inside the boat.

by cg it

real question would be why?

since the average wireless router's range is about 300 ft, unless your on a cruise ship what's the point?

by ramvicious

Sorry, I didn't say that, but I work on a steel towboat and it's almost impossible to get reception. We have the galley on one side with the wireless router, then engine room in the middle which is all steel and prevents any signal and then we have the sleeping quarters which is where I would like to be able to recieve signal.

by rjluvkc

I recommend installing a access point to the area you are wanting wireless access to.
The new AP needs a CAT5E cable run to where your existing Wireless router is and needs to be plugged into that. If your existing router has security enabled, I recommend configuring your new AP the same as your existing router that way you dont have to reconnect with different profiles if you go from one side of the boat to the other. Hope this helps.

by older mycroft

Or is everyone sitting around on wireless laptops surfing the 'net?

Any environment that consists of multiple physical impediments such as steel bulkheads, is hardly conducive to the use of wireless comms anyway. And since wireless protocols are way down the scale of anything approaching acceptable speed, I'm surprised anyone is using wireless at all.

You'd have more success and a far higher Kbps if you ran some Cat5E cabling to your preferred point of access.

The image of tugboat crew all competing simultaneously for a withering wireless signal due to the profusion of steel bulkheads, is one I have never imagined before.

Generally boat crew tend to work, eat, sleep in sharp succession and at some point check their email from a wired connection or a wireless connection in a designated area.

[i]Just my experience mind you.[/i] ;)

by ramvicious

Well, we do work 12-15 hours a day and we live on these boats for up to months at a time so we do eat, sleep, and work. Usually in that order. ^_^ It's just a lot more comfortable for us to be able to lay in bed and search the web than it would be to wait for our off watch to move our laptops into the gally and do our searching. So is the splitting the cable and running it to two different routers a no go?

by robo_dev

what you want to extend your wireless LAN is an Access Point (AP) or two.

An AP is basically like an ethernet hub, but is used for wireless. You don't want or need another router. A wireless router is the combination of a router and a wireless AP.

If you plug an WLAN AP into an ethernet port of your existing router, and configure it so the radio channel is different from your main wireless router, you can extend your wireless capability as far as you want.

Some APs use power-over-ethernet, which allows you to have the power supply where the router/switch is, and the AP just hangs out at the end of the ethernet cable you run for it. I would expect this would be useful for safety/convenience on a boat, as there are probably not 110V outlets everywhere, and the fewer cheap power supplies onboard, the better.

My favorite AP is the Netgear WAG102.

it supports Power over Ethernet (POE) and has all kinds of neat features. It's a metal box unit that can survive in up to 90% non-condensing humidity, but only 104F maximum temp.

www.netgear.com/Products/.../AccessPoints/WAG102.aspx

by thebofh

I recentley installed wireless hotspots in the hotel public areas and conference centre's. My setup is as follows:
2 ADSL modems bridged into firewall Hotspot server connected to firewall from fire wall I run to my core cisco switch on a different VLAN and from there to all the other cabinet switches. Keep the SSID name the same in all your AP's to secure your wireless disable the admin user name and create a new user name. to increase the securtity put the AP in hidden mode and only allow your mac adresses access.

Cheers
Brendan

This discussion is closed to new replies.