Discussion Locked

video card or motherboard?

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.

When I power up my computer, nothing shows on the monitor screen, eventhough the monitor is turned on. What can I do to resolve this issue? Thanks.

ross

13 replies

by mightyyoungfai

is there any sound comes out from your cpu? if there is, it meants one of your components is not complete insert.
try to plug all out and reconnect it.
or you may want to try change your display card. you can change to another agp/pci
anywhere good luck

by opatzg9

1. Is it under warranty? If it is merely check your connections between the monitor and pc and your power from the wall to pc and monitor. if they're all good send it in.
2. out of warranty and looking to fix, open the case and check you power supply by turning on the pc, are the fans turning? Do you hear the hard disk powering up? If it sound like everything is running ok, then shut it down, unplug, ground yourself to the pc chassi and then reseat (remove and push back into place) all add-on cards (modem, video, soudn, network...) and remove and reast all cables both the power connections to the drives and the ribbon cables from both motherboard and drives. plug it back in and try it again. If it's fixed great if not then
bring your system down to just the video,ram and motherboard components. Then add one peripheral at a time, hard disk, cd rom, sound, modem, ... til you narrow down what is causing the problem. Make sure you look at how the cables are attached since they should be reattached in the same direction. Make sure no pins got crushed and bent over. If they did you may be able to salvage with a needle nose pliers but they are very fragile. If you narrow it down more leave a message. Is there any beeping going on? Normally a pc will beep once while booting up.
Good luck

by bincarnato

Cut to the chase.
1. Power it on and see if you get any lights or activity on the CPU. If yes, go to next. If no, possible bad power supply.
2. Open the box and remove the memory. If you power the machine on and get beep codes, go to next. If no, then probable bad system board or possible processor, but no likely.
3. Remove all expansion cards and unplug all drives. Power on machine. If machine boots, go to next. If machine doesn't boot, probable bad system board or processor.
4. Start connecting drives one at a time and power on after each device is added. When machine doesn't boot after adding a device, that is the issue.

You may want to try swapping the video card out with a known good one or just putting one in and make sure to disable the onboard video if that is the case.

by krunch

First things first. Do you see lights on the keyboard when you fire it up and do you hear your fans running? If you get keyboard lights and internal fans then I'd plug in another monitor and see if you're going. If that fails, I would try an old video card - maybe you have an old pci card laying around? If that doesn't work, then you buy a $10.00 power supply tester from pc power and cooling: http://www.pcpowerandcooling.com/products/alarmandaccesories/accessories/popups/index_tester.htmMaybe you can try your current video card in another system? I see more video cards and monitors go out than I do mobo's but it could still be the culprit. Try the things I've suggested and let me know.

Cheers,

Krunch

by superman79

Ok before you do any of that other stuff, just get another monitor from somebody and connect it to your computer. If it works then your monitor cable is bad. Even though you see lights on the monitor it doesnt mean your getting a signal from the cp.ITs just the power that it might be getting. If the new one does the same thing then go ahead with the other stuff thats been explained by the other guys.

by captain krunch

I just worked thru this problem on an MSI K7T Turbo2 motherboard and it took clearing the CMOS and pulling the CMOS battery for 30 seconds and putting it back in to fix it. Something had gotten hosed in the BIOS and it was hanging in VGA BIOS verification. Oh yeah, I did all of the above. It hung on a Mobo, CPU & 1 stick of memory, wouldn't even beep once.

This discussion is closed to new replies.