Discussion Locked

What kind of problem do i have?

0 helpful
13 replies
Closed to new repliesThis discussion is closed. It stays readable, but it takes no new replies.
I rtecently tried to upgrade an old PC for my son.I put a new motherboard(bcm-in730se)and a new processor(amd duron 1.0Ghz).On start up the system shows as a amd athlon 1333Mhz and the computer will not come to full operation before locking up. I have tried to reinstall the operating system(win 98se)but so far i've had no luck. It also locks up in safe mode. HELP!

13 replies

by gpdunit164

IT appears that the computer is either ignoring the cd-rom or that the hard drive is locking up. i have tried the motherboard manufacturer with zero results. The hard drive is 8.5G with about 7.0G free. Any help would be greatly appreciated. Thanks in advance.

by gpdunit164

I appreciate the help you offered but the problem was caused by trying to put a 1000MHZ processor on a motherboard that only supported 850MHZ or less. Thanks for your help. Sorry for any inconvience.

by lord ago 1

First, I would check the CMOS settings and find anything that would indicate speed and core voltage for the cpu. Being detected as a 1333MHz when it's a 1.0 GHz sounds like it was or is overclocked. Also check for proper settings in the manual for the motherboard.
If it will still not boot up proper, boot into the Command Prompt(When it says Starting Windows 9x, press the F8 key). You can even use the bootdisk if need be. That won't hurt anything. Use DOS Edit or some other DOS based text editor and open the file(s) bootlog.txt and bootlog.prv.
Look for the word "Fail". That will at least point you in the direction of what was going wrong. These are both hidden files. So, type: edit bootlog.txt or .prv and they will show up anyway. Youdon't need to try to change them anyhow. Just look through them.
Also note that there are cases wherein parts will be useless/broken right out of the box. Seen that one many times over!!! As a last resort, if you still have a warranty, use it.

Have Fun!!!
Lord Ago 1

by dcosgrove

It is quite possible that you have a heat problem. Enter the bios and try to set the processor to it's correct speed. Also check that the heatsink and fan (including thermal compound) are properly installed. If the processor was not in a retail box and came without a heatsink, your old one will not work, you need a heatsink designed for that processor.

by thechas

If the BIOS and jumper settings for the CPU are correct,
Check the MB mfg web site for a BIOS update.

There is definetly a problem if the BIOS reports that the CPU is a higher frequency than it actually is.
I suspect that the Front Side Buss isset to 266MHz instead of the 200MHz specified for the Duron CPU.

Then, you need to install the chipset drivers in order to get the CD drive to function properly.

You may need to boot up from the startup disk, and copy the CD driver files over to the Hard drive so that you can install them from there.

Chas

by pinoy_teknik

The thing that i see is the processor was overclock.... that co'z your system to malfuctioning.. Overlocking means you make some parameters that the proccessor can speed-up by means of Increasing the system bus and the voltage core, for example.

So refer to the manual..adjust the multiplier, the jumper setting in the mboard and the bios...there should be a correct setup of system bus and voltage core.....

Most motherboard with AMD processor have ablity to overclock......

by gpdunit164

Thanks to everyone who tried to help me. The problem was an oversight on my part. I tried to put a 1000MHZ processor on a motherboard that would only support a processor of 850MHZ or less. I apologize for wasting everyones time. Thanks again for your help.

This discussion is closed to new replies.